Performance and Accessories 2nd gen only Talk about Dodge/Cummins aftermarket products for second generation trucks here. Can include high-performance mods, or general accessories.

map sensor or my commander?

Old May 29, 2008 | 06:42 PM
  #1  
MATTIEBOB's Avatar
Thread Starter
Registered User
 
Joined: May 2007
Posts: 273
Likes: 0
From: cleveland, oklahoma
map sensor or my commander?

today i noticed my commander at an idle was reading 1psi on boost, but then it would go back to 0psi it does it about every 30sec. or so. it keeps doing this, but idont think it is anything serious, im just curious as to what would cause this
Reply
Old May 30, 2008 | 05:29 PM
  #2  
MATTIEBOB's Avatar
Thread Starter
Registered User
 
Joined: May 2007
Posts: 273
Likes: 0
From: cleveland, oklahoma
any ideas?
Reply
Old May 30, 2008 | 05:42 PM
  #3  
JPR Ram's Avatar
Registered User
 
Joined: Jan 2007
Posts: 1,820
Likes: 2
From: My head lays down in Murrieta, but the day light hours are spent in San Diego, Ca.
I'd say the Commander. But then what do I know? I've never messed with one before.
Reply
Old May 30, 2008 | 05:47 PM
  #4  
vzdude's Avatar
DTR's 'Go to Guy'
 
Joined: Jan 2007
Posts: 3,811
Likes: 4
From: Indiana
More than likely it is just getting a little high resistance at the connection. Do you have the wire tap or the plug and play? I have to wiggle mine every now and again to get the boost to read right.
Reply
Old May 30, 2008 | 10:14 PM
  #5  
danalex's Avatar
Registered User
 
Joined: Dec 2007
Posts: 397
Likes: 5
From: Near San Antonio, TX
My boost (at idle) ALWAYS reads 8psi...dunno why, but it's done it since day one. I emailed quadzilla and they said to make sure I had the wire tapped correctly (done) and to make sure I had selected the correct vehicle (done). No change. I trust the other readings so I just ignore it...would like it to read correctly, but not sure its worth repeatedly messin' with it... -2cents
Reply
Old May 30, 2008 | 10:16 PM
  #6  
danalex's Avatar
Registered User
 
Joined: Dec 2007
Posts: 397
Likes: 5
From: Near San Antonio, TX
By the way, anybody know where (just in case) I can pick up a new MAP sensor? I've checked most Autozones/Oreily's and they don't seem to carry them. Tks. -d
Reply
Old May 30, 2008 | 11:06 PM
  #7  
xtoyz17's Avatar
Registered User
 
Joined: Nov 2006
Posts: 2,333
Likes: 0
From: Rochester, NY
Originally Posted by danalex
By the way, anybody know where (just in case) I can pick up a new MAP sensor? I've checked most Autozones/Oreily's and they don't seem to carry them. Tks. -d
Cummins, and I was actually going to say odds are good the sensor is bad.

Shawn
Reply
Old May 30, 2008 | 11:48 PM
  #8  
JPR Ram's Avatar
Registered User
 
Joined: Jan 2007
Posts: 1,820
Likes: 2
From: My head lays down in Murrieta, but the day light hours are spent in San Diego, Ca.
Try these guys. Their prices are very good. http://www.hoeslidiesel.com/specials.htm
Reply
Old May 31, 2008 | 12:58 AM
  #9  
MATTIEBOB's Avatar
Thread Starter
Registered User
 
Joined: May 2007
Posts: 273
Likes: 0
From: cleveland, oklahoma
i was thinking maybe the sensor too, because it also jumps around while driving, ie: i can be running 8psi and it will jump to 10psi and then back to 8psi. i talked to quad and they said it was probably getting a little bit more voltage and that it was more than likely the sensor
Reply
Old May 31, 2008 | 07:55 AM
  #10  
hink's Avatar
Registered User
 
Joined: Apr 2006
Posts: 695
Likes: 0
Originally Posted by JPR Ram
Try these guys. Their prices are very good. http://www.hoeslidiesel.com/specials.htm
That's where I got mine from. Good guys to do business with.
Reply
Old Jun 12, 2008 | 10:03 PM
  #11  
MATTIEBOB's Avatar
Thread Starter
Registered User
 
Joined: May 2007
Posts: 273
Likes: 0
From: cleveland, oklahoma
well i ordered my new map sensor from www.hoeslidiesel.com, and it is a little bit smaller in size than the factory one. it also takes a 1 1/16" socket instead of an 1 1/4" socket. is this the right part and will it work ok on my truck?

new map sensor part#4921497
Reply
Old Jun 12, 2008 | 10:55 PM
  #12  
hink's Avatar
Registered User
 
Joined: Apr 2006
Posts: 695
Likes: 0
Originally Posted by MATTIEBOB
well i ordered my new map sensor from www.hoeslidiesel.com, and it is a little bit smaller in size than the factory one. it also takes a 1 1/16" socket instead of an 1 1/4" socket. is this the right part and will it work ok on my truck?

new map sensor part#4921497
Their website says that part # covers 98.5-00, so you should be good.
I had to go buy a deep well 1 1/16 socket to change my MAP sensor, $26 for a socket from NAPA .
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
kawi600
Performance and Accessories 2nd gen only
4
Jun 13, 2009 04:26 PM
Moobesor
3rd Gen High Performance and Accessories (5.9L Only)
4
Feb 23, 2008 09:57 AM
kkyle69
24 Valve Engine and Drivetrain
5
Jul 7, 2007 12:33 PM
Gene007
24 Valve Engine and Drivetrain
0
Feb 26, 2006 04:31 PM
Booost Almighty
Performance and Accessories 2nd gen only
4
Jan 1, 2006 01:41 PM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 10:03 AM.