View Poll Results: When Will You Get To The Ranch?
Voters: 10. You may not vote on this poll
NT #8: May Meet
Registered User
Joined: Sep 2003
Posts: 2,534
Likes: 0
From: Plano, TX
Seriously....i think that would look tight on your ride.....even with the CTD "C" emblem......I would go with Flat black so it doesn’t look like you just painted over them! haha... Prime them up and then paint them flat black....would be inconspicuous but could be seen when looked at.....sticks with the theme....
Thread Starter
Chapter President
Joined: Oct 2002
Posts: 4,983
Likes: 1
From: Sedalia, Texas
OK, since I opened my mouth about the chili, I need to get a good count on "who and when". I know it's a week away, but I've added a poll so you can help with the info. 
Registered User
Joined: Jul 2004
Posts: 815
Likes: 1
From: Texas
Thread Starter
Chapter President
Joined: Oct 2002
Posts: 4,983
Likes: 1
From: Sedalia, Texas
Thread Starter
Chapter President
Joined: Oct 2002
Posts: 4,983
Likes: 1
From: Sedalia, Texas
Ha! Great song.
Registered User
Joined: Jul 2002
Posts: 2,242
Likes: 16
From: Celina, TX
The girlfriend is heading to OKC on Friday early, so I'll probably be headed to Sedalia early as well.
Anyone need anything from the Cummins shop? Might be making a run down there this week for a few parts.
Anyone need anything from the Cummins shop? Might be making a run down there this week for a few parts.
Thread Starter
Chapter President
Joined: Oct 2002
Posts: 4,983
Likes: 1
From: Sedalia, Texas
Good, see you Friday.
If they have them, injector o-rings and washers. Also, o-rings for the injector tubes. No biggie, but if your going...............
If they have them, injector o-rings and washers. Also, o-rings for the injector tubes. No biggie, but if your going...............
Registered User
Joined: Apr 2004
Posts: 8,234
Likes: 1
From: Texas/Oklahoma Border
I've been using Silicon hose, which is great for heat but is too soft.... my band clamps that hold it on keep cutting it and ripping off under pressure.
If they have right size with a good hard outer casing in it, I'd take 4' or so. (Gives me a future spare). Don't bother if any trouble...
I was going to run to McKinney Sat morn and look around anyway. The Cummins shop there is open Sat am, FYI.
El Presidente - You installing those Jammers??
RJ
Thread Starter
Chapter President
Joined: Oct 2002
Posts: 4,983
Likes: 1
From: Sedalia, Texas
While I'm here...............
I have jury duty on Thursday.....for the SECOND time in two weeks.
I've tried to get out of it, but they just don't understand mowing, trimming and Dodge diesel trucks.
So, I'll be at The Ranch late Thursday or sometime Friday.
Also, for you Newbies, don't forget your drinks, snack, chairs, sleeping arrangements (truck/tent), etc.
I have jury duty on Thursday.....for the SECOND time in two weeks.
I've tried to get out of it, but they just don't understand mowing, trimming and Dodge diesel trucks.So, I'll be at The Ranch late Thursday or sometime Friday.
Also, for you Newbies, don't forget your drinks, snack, chairs, sleeping arrangements (truck/tent), etc.
Thread Starter
Chapter President
Joined: Oct 2002
Posts: 4,983
Likes: 1
From: Sedalia, Texas
No to the Jammers. Just want to be ready to install or sell.
Justin, depending on what your looking for, but you might want to call Southwest International before you depend on them to have parts.
Justin, depending on what your looking for, but you might want to call Southwest International before you depend on them to have parts.
Justin, I need hose to make a new wastegate actuator/trubo connection.
I've been using Silicon hose, which is great for heat but is too soft.... my band clamps that hold it on keep cutting it and ripping off under pressure.
If they have right size with a good hard outer casing in it, I'd take 4' or so. (Gives me a future spare). Don't bother if any trouble...
I was going to run to McKinney Sat morn and look around anyway. The Cummins shop there is open Sat am, FYI.
El Presidente - You installing those Jammers??
RJ
I've been using Silicon hose, which is great for heat but is too soft.... my band clamps that hold it on keep cutting it and ripping off under pressure.
If they have right size with a good hard outer casing in it, I'd take 4' or so. (Gives me a future spare). Don't bother if any trouble...
I was going to run to McKinney Sat morn and look around anyway. The Cummins shop there is open Sat am, FYI.
El Presidente - You installing those Jammers??
RJ
Registered User
Joined: Apr 2004
Posts: 8,234
Likes: 1
From: Texas/Oklahoma Border
Looks like we're starting the party early Friday.
Tyler said he's due in around noon....
I'm taking the afternoon off....
Justins unencumbered by SHMBO!
Robert when he wakes up!
Brian?
I believe Okie gang is due in by 5-6 pm? Asked for a comfirmed ETA.
RJ
Tyler said he's due in around noon....
I'm taking the afternoon off....
Justins unencumbered by SHMBO!
Robert when he wakes up!
Brian?
I believe Okie gang is due in by 5-6 pm? Asked for a comfirmed ETA.
RJ
