Why does this bother me so much?
Thread Starter
"Gomer Pyle"
Joined: Nov 2010
Posts: 714
Likes: 2
From: NC
The "Not so Funny" think is that she actually blamed me. She said it would not have hapened if I bought something smaller. Kinda funny since she drives a full size SUV that is almost exactly the same width and length.
The Guru
Joined: Jan 2004
Posts: 6,589
Likes: 0
From: Airdrie Canada
I have a few dents inside the bed from loading engines into my bed. This is my first truck using that spray in bed liner. Next truck, I getting wood for a liner. My 02 bed liner has stood-up better than this spray in junk. Must have most it scrapped off on the bed floor.Anybody have that rear tail gate cap fall/blow off yet? Mines been gone for months now.
Sure look like chit with no plastic cover.
Registered User
Joined: Aug 2003
Posts: 3,604
Likes: 0
From: Jeffersonville, Ohio
Sorry to hear that buddy. Ya its a work truck, but... I have a few dents inside the bed from loading engines into my bed. This is my first truck using that spray in bed liner. Next truck, I getting wood for a liner. My 02 bed liner has stood-up better than this spray in junk. Must have most it scrapped off on the bed floor.
Anybody have that rear tail gate cap fall/blow off yet? Mines been gone for months now. Sure look like chit with no plastic cover.
I have a few dents inside the bed from loading engines into my bed. This is my first truck using that spray in bed liner. Next truck, I getting wood for a liner. My 02 bed liner has stood-up better than this spray in junk. Must have most it scrapped off on the bed floor.Anybody have that rear tail gate cap fall/blow off yet? Mines been gone for months now.
Sure look like chit with no plastic cover.I should have line-xed it, but never got around to it...so now it's just beat up in there!
Chris
The Guru
Joined: Jan 2004
Posts: 6,589
Likes: 0
From: Airdrie Canada
I have area's in my bed were the line-x stuff is peeled off in long chunks. Once I get the truck repainted, I going to get the bed liner re-applied, but its probably a waste of time.
I should have just bought another 2nd gen dodge truck, to be honest.
Registered User
Joined: Nov 2005
Posts: 72
Likes: 0
From: California & Colorado
has anyone done anything to limit paint chipping on the rocker panels and around the wheel well other than flares? Some cars and truck used to come with a bumpy type coating applied down low and it was then factory painted. I would like to do something because after only 4k miles my truck has tons of chipping behind the front wheels below the door.
Ya its a truck, but the newest and most expesive one I have ever purchased and I would like to try to keep it nice for at least a year or two...
Ya its a truck, but the newest and most expesive one I have ever purchased and I would like to try to keep it nice for at least a year or two...
Registered User
Joined: Oct 2010
Posts: 930
Likes: 13
From: Somewhere between Here & There Over the Hill
^^x2
I had Line-X spray the rocker panels and the bed on my 08. I like Line-X. Have you seen some of their videos? If it is peeling, its probably because the surface wasn't prepped properly.
Sent from my DROID X2 using Tapatalk
I had Line-X spray the rocker panels and the bed on my 08. I like Line-X. Have you seen some of their videos? If it is peeling, its probably because the surface wasn't prepped properly.
Sent from my DROID X2 using Tapatalk
Thread
Thread Starter
Forum
Replies
Last Post
terry1761
3rd Gen Engine and Drivetrain -> 2007 and up
24
Jan 29, 2008 09:12 AM
Buffman88
24 Valve Engine and Drivetrain
28
Dec 19, 2006 01:14 PM