1st Gen. Ram - All Topics Discussion for all Dodge Rams prior to 1994. This includes engine, drivetrain and non-drivetrain discussions. Anything prior to 1994 should go in here.

power ?

Old Jan 27, 2005 | 05:58 PM
  #1  
widetrak60's Avatar
Thread Starter
Registered User
 
Joined: Oct 2004
Posts: 71
Likes: 0
From: Alaska
Question power ?

I just orderd a 16 turbo houseing from pears and I have installed the bhaf, changed the gov spring and tweeked the pump like the tec page said to do (except I have not changed the pin). I advanced pump timing, I have a stock down pipe with 4" stright pipe dumping in front of rear tires (no bends tighter than 45deg) Can any one tell me about what power I'm going to have after I install the new housing? I dont have a place to put my truck on a dino but I see some of you have. I allso orderd a pyro gauge so I have not got on the throttle yet.
What can I expect? Ken
Reply
Old Jan 27, 2005 | 07:16 PM
  #2  
ARedetzke's Avatar
Registered User
 
Joined: Oct 2004
Posts: 79
Likes: 0
From: Manhattan, Kansas
275hp, maybe a little more
Reply
Old Jan 27, 2005 | 09:01 PM
  #3  
caleb c.'s Avatar
Registered User
 
Joined: Oct 2004
Posts: 648
Likes: 0
From: Lubbock TX.
275 with stock injectors?Is that rear wheel horsepower?I have about the same set up +/- his.I didn't think mine would be near that high.But thats cool if it is!
Reply
Old Jan 27, 2005 | 10:11 PM
  #4  
ARedetzke's Avatar
Registered User
 
Joined: Oct 2004
Posts: 79
Likes: 0
From: Manhattan, Kansas
My bad, missed the stock injectors. Throw some PODs in that bad boy, then you'll be around 275. Sorry, didn't mean to get you excited
AJ
Reply
Old Jan 28, 2005 | 01:00 AM
  #5  
widetrak60's Avatar
Thread Starter
Registered User
 
Joined: Oct 2004
Posts: 71
Likes: 0
From: Alaska
you had me going good with that 275 some PODs would be good but will have to wait. so any idea where I'm at now?
Reply
Old Jan 28, 2005 | 11:09 AM
  #6  
spunbearing's Avatar
Registered User
 
Joined: Nov 2003
Posts: 603
Likes: 0
From: Central Coast Ca
Minus about 50 HP for the PODS and I would think that you're around 200-225 HP
Reply
Old Jan 28, 2005 | 11:11 AM
  #7  
caleb c.'s Avatar
Registered User
 
Joined: Oct 2004
Posts: 648
Likes: 0
From: Lubbock TX.
I was thinkin that was alittle high!I can't wait to get the POD's in it and see what I get.And Smokey's pin and ats manifold and htt stage III and nv4500 trans and more pump work and stacks and...Man,I got it bad!
Reply
Old Jan 28, 2005 | 11:12 AM
  #8  
jiMMyCTD's Avatar
Registered User
 
Joined: May 2004
Posts: 936
Likes: 0
From: Diamond Springs, ca
sweet, im right on track for 300 then, i want the fuel pin and ill turn my screw in a tad more. should put me at 300 i would think. jiMMy
Reply
Old Jan 28, 2005 | 01:09 PM
  #9  
widetrak60's Avatar
Thread Starter
Registered User
 
Joined: Oct 2004
Posts: 71
Likes: 0
From: Alaska
cool thats a good start but I can see I need to do more
Reply
Old Jan 28, 2005 | 09:21 PM
  #10  
perkins's Avatar
Registered User
 
Joined: Oct 2001
Posts: 298
Likes: 0
From: Washington,Mo
We got my brothers 93 up to 318hp, with pod,hx35/14, power screw bottom out,stock gov.spring,4"ex,FASS lift pump,stock fuel pin turned to max depth.going to do more to the pump when we get the twins finnished.use his 35 with a HT3B
Reply
Old Jan 29, 2005 | 12:00 AM
  #11  
DBF's Avatar
DBF
Registered User
 
Joined: Feb 2003
Posts: 413
Likes: 0
From: Florida Panhandle
Re: power ?

Originally posted by widetrak60
Can any one tell me about what power I'm going to have after I install the new housing? I dont have a place to put my truck on a dino but I see some of you have. I allso orderd a pyro gauge so I have not got on the throttle yet.
What can I expect? Ken
I'm replying so you can see my sig and compare it with what you have. My truck has been on the Dynojet and did 195hp/495tq. I mainly use it for 5th-wheel towing.

Regards, DBF

PS: We'll be up your way this coming summer. I'd be happy to find you and swap stories for a few hours.
Reply
Old Jan 29, 2005 | 09:37 PM
  #12  
ChrisLib's Avatar
Registered User
20 Year Member
 
Joined: Dec 2003
Posts: 1,518
Likes: 11
From: Boerne, TX
Originally posted by caleb c.
I was thinkin that was alittle high!I can't wait to get the POD's in it and see what I get.And Smokey's pin and ats manifold and htt stage III and nv4500 trans and more pump work and stacks and...Man,I got it bad!
doessn`t it stink!!!!LOL! just look at what STOMP has done, very inspiring, altho I`d be happy to hit 350......yeah right .
Reply
Old Jan 29, 2005 | 10:39 PM
  #13  
Stomp's Avatar
Registered User
 
Joined: Jan 2004
Posts: 439
Likes: 0
From: Eureka,CA
Hey everybody has to start somewhere. I had a stock pickup once too. Well for a week or so. I have been modding mine for about 7 years now. It doesnt happen overnight unless you have access to a very big bank account or trust fund or win the lotto. Heck I remember when I just turned up my pump. I thought it was the fastest thing around. It may be fast now, but it's still ugly. It will get new paint, fenders, windshield, box, in the next couple of months. Also a new fuel pump to throw some more fuel at my twins.

Stomp

Edit: I guess I need to update my sig.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
RAK GUY
HELP!
3
Apr 5, 2003 10:28 PM
powerwagon440
Performance and Accessories 2nd gen only
3
Jan 20, 2003 08:50 PM
pwabbott
3rd Generation Ram - Non Drivetrain - All Years
14
Dec 20, 2002 08:23 PM
Garz
HELP!
3
Nov 17, 2002 02:02 PM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 04:15 PM.