This is a little embarrassing, but I was just kinda curious who the heck has the Wildcat Loaner Hole Saw? I had it scribbled down on my Palm Pilot, but after forgetting to charge the batteries, the info is loooong gone :-[<br><br>Rod

 

Did Jack finally cut the hole?

 

OK I am going to put the scotty II on my truck and have heard of this &quot;HUSH&quot; OR &quot;NO HUSH&quot;, and I hear about this HOLE CUTTING ... Where does this hole get cut at?

 

It cuts into the insulation and windsheild cowl right behind the turbo. I think. It should tell you in the instructions.

 

02DSLDOG, First install your Scotty II with the insulation at the fire wall folded back under the wiring harness. Mark where the filter housing fits the best and with a half inch chuck drill use the 4 1/2 inch hole saw. Having the ability to have the insulation still there is nice. Friends tease me that with the firewall open it sound as if the passengers change is being sucked out of their pockets into the vents. I run with it closed under normal driving conditions and open it for dyno runs, pulling, and hopfully this summer, drag racing. Hope this helps, Lon

 

I dunno where yours is rod but I have one I will loan to anyone for the cost of the shipping.

 

Probably stating the obvious, but have you gone through your invoices for whom you sold the Scotty II to and seems like a good candidate for having forgotten to return your Hole saw. Ain't technology great, palm pilots? Me, I'm still stuck with a pencil and paper pad. All I have to do is remember where I left the paper pad. :'(<br><br>~Dave

 

[quote author=NWDave link=board=7;threadid=13215;start=0#124755 date=1049634403]<br>Probably stating the obvious, but have you gone through your invoices for whom you sold the Scotty II to and seems like a good candidate for having forgotten to return your Hole saw. [/quote]<br><br>&lt;chuckle&gt; Yep, did that, but no-ones got it. I'm beginning to wonder if the hole saw didn't go missing in transport. Right now, I've probably got a customer ticked right off at me because I didn't send them the loaner saw I promised to.<br><br>Rod

 

[quote author=Push Rod link=board=7;threadid=13215;start=0#124776 date=1049641972]<br>[quote author=NWDave link=board=7;threadid=13215;start=0#124755 date=1049634403]<br>Probably stating the obvious, but have you gone through your invoices for whom you sold the Scotty II to and seems like a good candidate for having forgotten to return your Hole saw. [/quote]<br><br>&lt;chuckle&gt; Yep, did that, but no-ones got it. I'm beginning to wonder if the hole saw didn't go missing in transport. Right now, I've probably got a customer ticked right off at me because I didn't send them the loaner saw I promised to.<br><br>Rod<br>[/quote]<br><br>[move]It's all a dream there never was a hole saw [/move]<br><br>[move]ONLY SHEEP AND PENGUINS !!!!![/move]<br><br> ;D<br><br> : Eddie : 8)

 

Rod,<br> This is the model of Palm Pilot that I use. Never have to worry about losing information ... unless you get too close to soap and water .<br><br>PISTOL

 

 

 

 

[quote author=PistolWhipt link=board=7;threadid=13215;start=0#124836 date=1049659689]<br>Rod,<br> This is the model of Palm Pilot that I use. Never have to worry about losing information ... unless you get too close to soap and water .<br><br>PISTOL<br>[/quote]<br><br>Ya mean they got a newer one than mine? <br>Shoot! Mine didnt come with the input device attacment string!<br>Keep loosing that input device everywhere I go!<br><br>Time for an upgrade! <br> <br>Rich

 

I've found that rolling up my sleeve increases my memory capacity.