Next GTG???
#2
Registered User
Join Date: Aug 2006
Location: Fort McMurray, Alberta
Posts: 5,426
Likes: 0
Received 0 Likes
on
0 Posts
I personally am pretty much hooped till the new year. And even then it would be the chevy,, the old dodge is going through some major changes and I doubt it will be done much before spring
Kevin
Kevin
#5
The Guru
Join Date: Jan 2004
Location: Airdrie Canada
Posts: 6,589
Likes: 0
Received 0 Likes
on
0 Posts
I'm in, just sooner than later. Might give me a reason to pull some wrenchs. Worst case is that I have a 08 hemi 1500. Its still a dodge ram. I'm still working on the trusty old 02 just breakin the motor ride. It would good to see everyone again, and at least get in some intelligent truck talk. Not that usual my GMC/ford is cooler than your stuff that I hear way too often these days.
#6
Registered User
Join Date: Oct 2007
Location: High River, Alberta
Posts: 511
Likes: 0
Received 0 Likes
on
0 Posts
I'm in. It would be awsome to strap to a dyno if there was one around, lots of new toys to test out since the last numbers. Should be close to 400-450 now hopefully, my goal is a consistant reliable 500 by springtime, just want to find out how close I am, and hear any suggestions on what to do next.
I'm always up for talkin diesel, even if they aren't of the Inline species.
Fred.
I'm always up for talkin diesel, even if they aren't of the Inline species.
Fred.
Trending Topics
#8
Registered User
Join Date: Dec 2006
Location: Red Deer, Alberta
Posts: 303
Likes: 0
Received 0 Likes
on
0 Posts
I would be in for either a bull or dyno session as long as work doesn't get in the way. I have been waiting for my brother to get his stage 3 pump so we can book some dyno time and see what my beast is good for and to get his twins dialed in.
#10
Registered User
Join Date: Dec 2006
Location: Red Deer, Alberta
Posts: 303
Likes: 0
Received 0 Likes
on
0 Posts
I just got a bigger single my brother is the one that put twins on his 05 he went with 62/71/13 over a S480 from MPI. A very nice setup, spooling is very fast and they are actually fairly quite even at 65psi, quite a bit quieter then my 64/71/14.
#11
Chapter President
Busy? Me? That being said, a GTG would be good before Christmas. We usually have a nose-drippin event around this time. Need a new venue for a meet as Ray is now out in Alix and haven't heard from him since.
Whats up DD? Got your Gen1 engine yet?
Whats up DD? Got your Gen1 engine yet?
#12
The Guru
Join Date: Jan 2004
Location: Airdrie Canada
Posts: 6,589
Likes: 0
Received 0 Likes
on
0 Posts
Lil dog, do you think we could get the dyno set-up or do we need a certain amount of truck to run? Too bad we just couldn't rent the dyno for the day and run two to three each. If we even get 4 to 6 trucks, we should be covered. I bet we could have a decent showing again. My truck fired up again, its cursed but its running. I like to see if I can break out of the 500rwhp club.
#14
Registered User
Thread Starter
Join Date: Mar 2005
Location: Red Deer, Alberta
Posts: 3,190
Likes: 0
Received 0 Likes
on
0 Posts
Been way too busy with work. Got to go get it from Edmonton one of these weekends. It's a complete truck so if there are and extra parts takers, PM me..
#15
Registered User
Join Date: Aug 2005
Location: Airdrie, Alberta
Posts: 7,780
Likes: 0
Received 0 Likes
on
0 Posts
Lil dog, do you think we could get the dyno set-up or do we need a certain amount of truck to run? Too bad we just couldn't rent the dyno for the day and run two to three each. If we even get 4 to 6 trucks, we should be covered. I bet we could have a decent showing again. My truck fired up again, its cursed but its running. I like to see if I can break out of the 500rwhp club.