Loud injectors
#1
Registered User
Thread Starter
Join Date: Jan 2007
Location: Home of the Beaver
Posts: 685
Likes: 0
Received 0 Likes
on
0 Posts
Loud injectors
hey so I up-graded my injection pump to a stage 2. Idle pressure 20k plus. Noticed right away that the injectors are way louder is this normal?
TIA
onetun
TIA
onetun
#5
Registered User
Thread Starter
Join Date: Jan 2007
Location: Home of the Beaver
Posts: 685
Likes: 0
Received 0 Likes
on
0 Posts
alright what should my idle pressure be and how?? much louder is a modded pump.
Hey Don ran the truck for a hour, did a mess something up??
Hey Don ran the truck for a hour, did a mess something up??
#6
Registered User
Join Date: May 2004
Location: B.C. Canada
Posts: 616
Likes: 0
Received 0 Likes
on
0 Posts
No way you got 20,000 psi railpressure at idle. A faulty FCA will send rail pressure to the max but you said Don ran them How are you getting that number? What gauge are you using? Yes with upgrade injectors it can be louder depending on what you had installed. What injectors are in now?
#7
Registered User
Thread Starter
Join Date: Jan 2007
Location: Home of the Beaver
Posts: 685
Likes: 0
Received 0 Likes
on
0 Posts
No way you got 20,000 psi railpressure at idle. A faulty FCA will send rail pressure to the max but you said Don ran them How are you getting that number? What gauge are you using? Yes with upgrade injectors it can be louder depending on what you had installed. What injectors are in now?
I was trying to say Hey Don, "I" ran the truck for an hour did I mess something up.
Rail pressure gauge Dipricol.
When I first fired the engine I looked at my pressure and it was over 20k. I was not sure if it was normal or not so I let the truck idle for a bit then went for a burn. Noticed right away pressure gauge was all over the place from 10-25k. Truck performed fine, and was very responsive.
All other areas of the engine seem to be in check i.e fuel pressure, egts, boost...............
So how do I confirm a have a faulty FCA, and in testing this what pressures am I targeting??
I'm running Flux 2 sticks
onetun
Trending Topics
#8
might have a sticking fca. here's a pic of it, the link to the CP3 mod page is the bottom one, with good pics and directions to ensure it isnt sticking, and how to fix it. the topic is for a mod, that wont do you any good since you have a stage 2, but the discussion on the fca sliding smoothly will help you.
[IMG][/IMG]
http://relentlessdiesel.com/forum/viewtopic.php?t=19
[IMG][/IMG]
http://relentlessdiesel.com/forum/viewtopic.php?t=19
#11
Registered User
Thread Starter
Join Date: Jan 2007
Location: Home of the Beaver
Posts: 685
Likes: 0
Received 0 Likes
on
0 Posts
might have a sticking fca. here's a pic of it, the link to the CP3 mod page is the bottom one, with good pics and directions to ensure it isnt sticking, and how to fix it. the topic is for a mod, that wont do you any good since you have a stage 2, but the discussion on the fca sliding smoothly will help you.
[IMG][/IMG]
http://relentlessdiesel.com/forum/viewtopic.php?t=19
[IMG][/IMG]
http://relentlessdiesel.com/forum/viewtopic.php?t=19
Zilla,
Thanks for the info,
#13
Registered User
Join Date: May 2004
Location: B.C. Canada
Posts: 616
Likes: 0
Received 0 Likes
on
0 Posts
Oneton
Remove the FCA and shake it. If it rattles the cylinder is sliding in the bore, all good. Next check the connection pins and harness. Finally go over the dipricol connection to the rail sensor. Something has to be wrong with the connection. Above all, don't run the engine if your gauge checks out correct and is not at fault
Remove the FCA and shake it. If it rattles the cylinder is sliding in the bore, all good. Next check the connection pins and harness. Finally go over the dipricol connection to the rail sensor. Something has to be wrong with the connection. Above all, don't run the engine if your gauge checks out correct and is not at fault
#14
#15
Registered User
Thread Starter
Join Date: Jan 2007
Location: Home of the Beaver
Posts: 685
Likes: 0
Received 0 Likes
on
0 Posts
Pulled the FCA
shook it no rattle. Have a replacement on its way, I guess I will be more diligent when doing up-grades. Never thought to ask what kind of rail pressure at idle.
Hopefully I never ruined my sticks.
onetun
Hopefully I never ruined my sticks.
onetun