Come one come all....bring your Ford and Chevy Buddies......

After our last get together, guys said they wanted to compair their HP numbers from the Mustang to a Dyno Jet. Other have done some more modifications.

So here it is:

HiTech Motorsports in Ramsey (http://www.hitechmotorsport.com/). If we have more than 10 trucks it's $50 each. Less than 10 $60. Start time around 9am. We get 2 CLEAN runs Back to Back. They have the optical pick-up so we do get a torque reading. They Drive the truck on the dyno. Duallys, gotta take the outside dual off. If the Ford or Chevy guys bring a 4door long bed...sorry guys it won't fit. We were there last year, Bart and Brian are great guys. Last time, we amiazed them with the HP and Torque that our trucks produce. Lets show them again!

Directions are Easy! From the Cities, get on HWY 10 west towards Anoka. Go to Sunfish Lake Blvd, take a right (north) go over the rail road tracks and take your first Right. Follow that down a few block till you see Airgas, take a left, the building is on the right.

From the West: Take HWY 10 east towards the cities, Go to Sunfish Lake Blvd, take a left (north) go over the rail road tracks and take your first Right. Follow that down a few block till you see Airgas, take a left, the building is on the right.

I will try to have a sign up in front of the building, but due to the Frozen ground or lack of snow...I may not be able to.

Any questions feel free to ask!

Josh

 

Dang, that sounds like fun!! I will do my best to be there. I just need to figure out where to get the dyno fee

 

WELL SHOOT!!!!! My wife informed me that I need to be at my Union Hall Dec. 2 for a mandatory 8 hours of continuing education in order to keep my Power Limited Electrical License. DARN!!!

 

Tom, I may not be the best with numbers, but I know that the dyno day is on the 4th, and you said you were busy on the 2nd I tell ya what, if I don't have hockey you bet I'm going to be there! Gotta get a sheet to go along with the smoke...

 

Sorry, I meant Dec. 4 I need to be at my Hall by 8am and won't get done 'till4:30pm. I did want to spin the rollers too.

 

I'll have to wait until we get a little closer, but I sure plan to be there.


What is that? Does it say EZ in my sig now???

 

What is that? Does it say EZ in my sig now???
I KNEW you could not hold out very long Andy!!!

 

E - D - G - E E - Z

Yep, I think it does What, no injectors

 

Gotta beef up that tranny first. Still looking for that high paying, no effort side job.

 

If ya want to come clean my garage after I get done this weekend, that would count as a high effort no paying side job... Or were you looking for the other way around

 

Well I guess I'll have to try to make it up there it's only a 3 hour drive from Winona. I drive easy. Gotts to save the fuel for the test. haha.
I will need some help with the duals however as I'm stranded from home with no tools.
Looking forward to seeing some soot. LOL ...not on me this time. HaHa

Might even know some of y'all as I used to live in St. Paul,Duluth,Virginia

 

Don't worry about the duals. We will bring tools, so we can take them off that day.

Josh

 

this is the same place i dyno'ed at this july. Bart is a great guy! i am now living in Bozeman, Montana so i will not be able to make it. too bad because when i dyno'ed the comp wire had come loose before i made my dyno runs and could never get over 366hp. of course, when i got home i figured out what was wrong. i was too excited during the dynoing that i didnt think straight. Bart gets really excited with the big diesel power and torque, its great.

have fun, Pat

 

What time does this soot party start???

Looks like they have a nice shop with a big vent so I guess we won't have soot rolling out the doors like some do. LLOL

 

The party starts at 9am.