MDDTR #33 Forum for the Maryland chapter #33

Edge system

Old Feb 4, 2009 | 09:39 AM
  #1  
usmarine110786's Avatar
Thread Starter
Registered User
 
Joined: Sep 2008
Posts: 47
Likes: 0
From: Bowleys Quarters, MD
Edge system

i got my edge juice with attitude in but it still dont work the only thing it does is read the egts and trans temp. it wont change levels, it reads 0 fuel press, and wont fuel past 2200 rpms.
Reply
Old Feb 5, 2009 | 06:17 AM
  #2  
scottsjeeprolet's Avatar
Chapter President
 
Joined: Aug 2004
Posts: 3,481
Likes: 2
From: Kingsville, MD
Chris post this over in the 2nd gen performance section.
You can bring it over and we can have a look at it.
Have you called Edge about it?
Reply
Old Feb 5, 2009 | 12:35 PM
  #3  
dzlfarmboy's Avatar
Registered User
 
Joined: Mar 2006
Posts: 1,140
Likes: 0
From: Eastern Shore of Maryland
And you have everthing hooked up right? Map sensor, Pump wire tapped,data conection link hooked up and the unit hooked up with a key on power.
Reply
Old Feb 5, 2009 | 01:31 PM
  #4  
usmarine110786's Avatar
Thread Starter
Registered User
 
Joined: Sep 2008
Posts: 47
Likes: 0
From: Bowleys Quarters, MD
yea i hooked everything up and called edge they said i would have to take it to an instlitation specialist. i will bring it over whenever ur free to look at it just let me know thanks.
Reply
Old Feb 7, 2009 | 02:58 PM
  #5  
06 DIESEL's Avatar
Registered User
 
Joined: Jul 2007
Posts: 1,473
Likes: 2
From: Kingsville, Md
He is over here now and everything is hooked up properly as far as I can tell. I did pull four codes though

P-0500 - Vehicle speed sensor malfunction

P-1693 - DTC Detected in companion mode

P-1694 - Fault in Companion Mode

P-1687 - No Cluster bus message

Since I do not have access to a code reader/clearer here for a second gen I am asking that someone out there that has the ability to do with to a second gen please send Chris a PM and try to hook up with him to get these codes cleared.
Reply
Old Feb 7, 2009 | 05:46 PM
  #6  
06 DIESEL's Avatar
Registered User
 
Joined: Jul 2007
Posts: 1,473
Likes: 2
From: Kingsville, Md
I think we might have found the problem. His positive battery terminals were loose so we tightened them. He also had a deal lift pump so we replaced that. The truck seems to be running better now, I will let Chris chime in and let us know how the drive home was.
Reply
Old Feb 7, 2009 | 05:50 PM
  #7  
06MegaCTD's Avatar
Registered User
 
Joined: Feb 2008
Posts: 732
Likes: 0
From: Elkridge, MD
**** ya'll had a spare lift pump in the cave lol.
Reply
Old Feb 7, 2009 | 07:35 PM
  #8  
biggerkin's Avatar
Registered User
 
Joined: Dec 2006
Posts: 329
Likes: 0
From: Rising Sun, MD
Talking you never know

whats in the cave
Reply
Old Feb 7, 2009 | 07:44 PM
  #9  
06 DIESEL's Avatar
Registered User
 
Joined: Jul 2007
Posts: 1,473
Likes: 2
From: Kingsville, Md
Yes there was one in the cave but we were not sure if it worked or not. He bought one at Salvo that has a lifetime warranty, so he is good now.
Reply
Old Feb 7, 2009 | 11:15 PM
  #10  
md-rebel's Avatar
Registered User
 
Joined: May 2006
Posts: 388
Likes: 0
From: Baltimore, Maryland
Originally Posted by biggerkin
whats in the cave
No one really knows ......... (add creepy laugh)
Reply
Old Feb 8, 2009 | 12:03 PM
  #11  
usmarine110786's Avatar
Thread Starter
Registered User
 
Joined: Sep 2008
Posts: 47
Likes: 0
From: Bowleys Quarters, MD
well i still have codes thrown and i need to get the ecp reset on the truck if anyone knows where i can get the computer reset.
Reply
Old Feb 8, 2009 | 02:40 PM
  #12  
scottsjeeprolet's Avatar
Chapter President
 
Joined: Aug 2004
Posts: 3,481
Likes: 2
From: Kingsville, MD
We have a code reader at work. I'll bring it home and we can clear the codes with it.
Reply
Old Feb 8, 2009 | 07:17 PM
  #13  
lukedaemon's Avatar
Registered User
 
Joined: Sep 2007
Posts: 340
Likes: 0
From: Gunpowder, MD
I have a scanner/reader too. Not the top of the line type, but does the job.
Reply
Old Feb 8, 2009 | 09:10 PM
  #14  
rollincoal02's Avatar
Banned
 
Joined: Mar 2008
Posts: 292
Likes: 0
From: Back to the city :(
find someone with a smarty local...it will clear the codes
Reply
Old Feb 9, 2009 | 08:29 AM
  #15  
bootsdodgejn's Avatar
Registered User
 
Joined: Jun 2007
Posts: 1,060
Likes: 0
From: jarretsville.
Originally Posted by 06 DIESEL
He is over here now and everything is hooked up properly as far as I can tell. I did pull four codes though

P-0500 - Vehicle speed sensor malfunction

P-1693 - DTC Detected in companion mode

P-1694 - Fault in Companion Mode

P-1687 - No Cluster bus message

Since I do not have access to a code reader/clearer here for a second gen I am asking that someone out there that has the ability to do with to a second gen please send Chris a PM and try to hook up with him to get these codes cleared.

I know i always have. Vehicle speed sensor malfunction code. Going to check into at school today in advanced diag class.
Reply

Thread Tools
Search this Thread

All times are GMT -5. The time now is 04:28 PM.