Fall GTG/Dyno Red Deer Sept 26.
Registered User
Joined: Jun 2006
Posts: 954
Likes: 0
From: Airdrie, AB
The Guru
Joined: Jan 2004
Posts: 6,589
Likes: 0
From: Airdrie Canada
Fred, Its so close buddy but I have no fuel, my little sticks are tiny little things. I want my mach 6er's freshen up. I think that a K-31 would be a better choice for the GT3788R.
You tapping the pump for the dyno event? You should be able to make some decent ponies.
You tapping the pump for the dyno event? You should be able to make some decent ponies.
The Guru
Joined: Jan 2004
Posts: 6,589
Likes: 0
From: Airdrie Canada
dvst8r, If we could get that manifold done by friday, it would one nice piece buddy....just need more time.
and I want to run that external gate so badly, just so we can get the primary to lite decently. Anyways, I might have said to much already.
and I want to run that external gate so badly, just so we can get the primary to lite decently. Anyways, I might have said to much already.
Registered User
Joined: Jun 2006
Posts: 954
Likes: 0
From: Airdrie, AB
Did you find a tight 3" 90?
We need one of these in aluminum and one in steel, too bad we are short on time... http://www.racepartsolutions.com/pro...prod=RPS-DONUT
I am certain we can find something that will work.
We need one of these in aluminum and one in steel, too bad we are short on time... http://www.racepartsolutions.com/pro...prod=RPS-DONUT
I am certain we can find something that will work.
Registered User
Joined: Jun 2006
Posts: 954
Likes: 0
From: Airdrie, AB
These work well too http://www.summitracing.com/parts/HOK-12399HKR/
3" diameter, 4" CLR. That 3" U bend you have is probably a 6" CLR
3" diameter, 4" CLR. That 3" U bend you have is probably a 6" CLR
The Guru
Joined: Jan 2004
Posts: 6,589
Likes: 0
From: Airdrie Canada
Thats the answer buddy. I'll order the tubes tomorrow. Thanks man, I owe ya.
Ya, that 3in 180deg bend that I have is just a big ugly pile. It was a good idea at the time. Most people think that 3in is too small, but for small twins its the hot ticket, as your spool-up would be wicked. A 3in short 180 deg, about 4 to 6in long between the both turbos (for both the hot/cold sides). I might be drooling.
Ya, that 3in 180deg bend that I have is just a big ugly pile. It was a good idea at the time. Most people think that 3in is too small, but for small twins its the hot ticket, as your spool-up would be wicked. A 3in short 180 deg, about 4 to 6in long between the both turbos (for both the hot/cold sides). I might be drooling.
Registered User
Joined: Sep 2007
Posts: 73
Likes: 0
I wont be making it, doesnt look like the head is going to be here till the end of the week so I'll be putting my truck back together on Saturday hopefully. Have fun at the dyno lay the smack down on the gassers.
Registered User
Joined: Mar 2007
Posts: 1,245
Likes: 17
From: Calgary, Alberta, Canada
I see that Diesel Dave has posted all the details of this GTG on ABdiesels.com..
I just did the same on CumminsForum. The more the merrier!
Is anyone on here coming down from Edmonton for this?
I have 2 small packages for an Edmonton member from my Montana trip that has to go to Edmonton.
What time should the Cgy folks meet at Tim's/Crossfield?
...Joe
I just did the same on CumminsForum. The more the merrier!
Is anyone on here coming down from Edmonton for this?
I have 2 small packages for an Edmonton member from my Montana trip that has to go to Edmonton.
What time should the Cgy folks meet at Tim's/Crossfield?
...Joe
Thread Starter
Chapter President
Joined: Feb 2002
Posts: 6,102
Likes: 2
From: Red Deer, Alberta Canada
A bit of change in plans---may make it for a bit-----some dumba$$ tree cutter working for a contractor decided to lay a tree across my chain link fence at the lake last weekend,took out 30+ feet and then tried to straighten it so i wouldn't notice
.No phone call/NOTHING,i'll fix it since i built it the first time but there a big bill coming his way(parts/labor),hopefully a good profit to buy some mods---if i don't make it good luck to every one and hopefully see you at the Oct show.DW
.No phone call/NOTHING,i'll fix it since i built it the first time but there a big bill coming his way(parts/labor),hopefully a good profit to buy some mods---if i don't make it good luck to every one and hopefully see you at the Oct show.DW
Thread Starter
Chapter President
Joined: Feb 2002
Posts: 6,102
Likes: 2
From: Red Deer, Alberta Canada
Registered User
Joined: Apr 2005
Posts: 757
Likes: 0
From: Calgary/Alta
THANKS for the offer(s)----should not take me long to do but it just one more thing to an already busy schedule.Still going to try to make it maybe for a bit,wife will have the 07 with her and i really want to polish up old blue one or two more times this year before winter.Hopefully the fence can wait,probable take me 3-4 hours to complete if no digging.I do have to work on Sat but going to hit the road by 11:00 AM if no problems---maybe show before 1:00.-----DW
Registered User
Joined: Jul 2008
Posts: 322
Likes: 0
From: Edmonton, Alberta
That would be me, I'd sure appreciate it if any edmontonians are making the trip. I'm still working on Baffin Island for a few more days and wont be able to make it to this GTG...but Joe, if you are going to the one in Oct . I can get the truck stuff from you then. thanks, D
Registered User
Joined: Jul 2008
Posts: 322
Likes: 0
From: Edmonton, Alberta
That'd be sweet, thanks for the offer. I'll be back in town by then, and I could meet you at Castrol. Are you racing?