Lets see your gauges! (picture thread)
#1
Registered User
Thread Starter
Join Date: Jan 2008
Location: Quinton, New Jersey (middle of nowhere)
Posts: 7,547
Likes: 0
Received 2 Likes
on
2 Posts
Lets see your gauges! (picture thread)
Never seen a thread like this. Figured it'd be a good thread for people thinking about gauges and so we can drool over each others setups! Post em' up!
The 93. Autometer Pyro/Boost with factory tach mounted on the column. Need to pickup a fuel PSI gauge.
Only rule is Richie_O can't post his because we've all seen them 10 times j/k
Brandon
The 93. Autometer Pyro/Boost with factory tach mounted on the column. Need to pickup a fuel PSI gauge.
Only rule is Richie_O can't post his because we've all seen them 10 times j/k
Brandon
#3
Registered User
Thread Starter
Join Date: Jan 2008
Location: Quinton, New Jersey (middle of nowhere)
Posts: 7,547
Likes: 0
Received 2 Likes
on
2 Posts
how'd i know you'd be the 1st one to post in here... you must search your username in the 1st gen section to see who's been talking about you when you weren't around
#5
Registered User
Join Date: Sep 2009
Location: Carencro, LA (near Lafayette)
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
Never seen a thread like this. Figured it'd be a good thread for people thinking about gauges and so we can drool over each others setups! Post em' up!
The 93. Autometer Pyro/Boost with factory tach mounted on the column. Need to pickup a fuel PSI gauge.
Only rule is Richie_O can't post his because we've all seen them 10 times j/k
Brandon
The 93. Autometer Pyro/Boost with factory tach mounted on the column. Need to pickup a fuel PSI gauge.
Only rule is Richie_O can't post his because we've all seen them 10 times j/k
Brandon
#6
Registered User
Thread Starter
Join Date: Jan 2008
Location: Quinton, New Jersey (middle of nowhere)
Posts: 7,547
Likes: 0
Received 2 Likes
on
2 Posts
Its sheetmetal with a pebel grain and its custom.
thread-
https://www.dieseltruckresource.com/...=gauge+install
thread-
https://www.dieseltruckresource.com/...=gauge+install
Trending Topics
#9
Registered User
Join Date: Jan 2009
Location: Bountiful, Utah
Posts: 2,128
Likes: 0
Received 0 Likes
on
0 Posts
Here's mine, Isspro EV boost and egt gauges in the autometer pillar pod and tach in the dash pod (which is actually off an old snowmobile) and some custome paint. I am building a new dash pod out of diamond plate so I should have it done this week and I'll take pics of that installed because the one on there now doesn't fit the best. I still need a trans temp and fuel pressure gauge to fill in the two empty holes.
#10
Registered User
unfortunately the gauges were put in the truck years ago. if it were me, i wouldn't have drilled holes in the dash. but, can't do anything about that now. anywho, here's a before with a non-working pyro.... breathe! it's ok, the pump was and still is stock.
and here's after. even though nothing's change except for the pyro was replaced. now i just need a matching boost and fuel psi gauge to go with it. i'll more than likely buy a dual and single gauge a-pillar pod and stack them. the tack may have to move a bit to make room for the pillar pod.
and here's after. even though nothing's change except for the pyro was replaced. now i just need a matching boost and fuel psi gauge to go with it. i'll more than likely buy a dual and single gauge a-pillar pod and stack them. the tack may have to move a bit to make room for the pillar pod.
#15
Registered User
Simialr to Brandon's, except I relocated the message center to the radio spot. Since I like to drive around topless, I figured no radio for the tweakers to steal.