Dodge Diesel - Diesel Truck Resource Forums
0 2024/08/19 19:05:52
0 2024/08/19 19:05:47
0 2024/08/19 19:05:41
0 2024/08/18 06:34:27
It finally saw daykight for the 1st time in 10 months under its own power
It finally saw daykight for the 1st time in 10 months under its own power
0 2024/08/18 06:34:23
I had to pull the clutch apart because someone installed it incorrectly. I'm going to fire my help.
I had to pull the clutch apart because someone installed it incorrectly. I'm going to fire my help.
0 2024/08/18 06:34:12
I pulled this one from a 91.5 W250 to use in a 3rd gen hydro unit, but went with a new Valair adjustable master cylinder set up.
I pulled this one from a 91.5 W250 to use in a 3rd gen hydro unit, but went with a new Valair adjustable master cylinder set up.
0 2024/08/16 03:15:02
I pulled this out of a 91.5 W250, to use in a 3rd gen clutch but went with a new Valair adjustable lenght unit.
I pulled this out of a 91.5 W250, to use in a 3rd gen clutch but went with a new Valair adjustable lenght unit.
0 2024/08/16 03:11:53
0 2024/08/16 03:09:52
0 2024/08/16 03:09:09
Its back on all 4 wheels
Its back on all 4 wheels
0 2024/08/11 07:03:18
Wiring harnesses are in and everything seems to work as it should.
Wiring harnesses are in and everything seems to work as it should.
0 2024/08/11 07:03:12
As i mentioned before this project is time consuming and nothing from the second gen fits this first gen without a lot of re-engineering. I had to move the battery tray about an inch towards the fender and clearance the inner fenders for cooler tubes
As i mentioned before this project is time consuming and nothing from the second gen fits this first gen without a lot of re-engineering. I had to move the battery tray about an inch towards the fender and clearance the inner fenders for cooler tubes
0 2024/08/11 06:57:12
0 2024/08/11 06:57:07
0 2024/08/11 06:57:02
0 2024/08/11 06:56:57
I got the old fenders fitted back on the truck, adjusted both front doors so they close correctly, and aligned the hood. The body parts lined up good enough for a few shake down miles.
I got the old fenders fitted back on the truck, adjusted both front doors so they close correctly, and aligned the hood. The body parts lined up good enough for a few shake down miles.
0 2024/08/11 06:52:42
0 2024/08/11 06:52:38
0 2024/07/20 07:09:25
0 2024/07/20 07:09:20
0 2024/07/20 07:09:15
0 2024/07/20 07:09:09
0 2024/07/20 07:09:03
I used a the 2nd gen radiator shroud with some trimming and a Non IC fan behind the new radiator
I used a the 2nd gen radiator shroud with some trimming and a Non IC fan behind the new radiator
0 2024/07/20 07:08:57
This JC Whitney tube grill, that i found in a junkyard many moons ago, is coming in clutch for this job.
This JC Whitney tube grill, that i found in a junkyard many moons ago, is coming in clutch for this job.
0 2024/07/20 07:04:13
I finally got the core support to comply with this project, and it recieved the same treatment as the inner fenders. 1985 Mopar Navy Blue over black primer.
I finally got the core support to comply with this project, and it recieved the same treatment as the inner fenders. 1985 Mopar Navy Blue over black primer.
0 2024/07/20 07:04:09
I had a set of decent inner fenders that got patched, blasted and expoxied, followed by single stage paint that was supposed to be flat.
I had a set of decent inner fenders that got patched, blasted and expoxied, followed by single stage paint that was supposed to be flat.
0 2024/07/20 07:04:03
0 2024/07/20 07:03:58
0 2024/07/20 07:00:35
0 2024/07/20 07:00:30
0 2024/07/20 07:00:25
0 2024/07/20 07:00:20
0 2024/07/20 07:00:15
0 2024/07/20 07:00:09
0 2024/07/20 07:00:00
This will be the face of this ride. Note the hard trimming of the valence to clear the 2nd gen cooler. I think this would all fit behind a big plastic IC grill, but thats what everyone else does.
This will be the face of this ride. Note the hard trimming of the valence to clear the 2nd gen cooler. I think this would all fit behind a big plastic IC grill, but thats what everyone else does.
0 2024/07/20 06:52:00
0 2024/07/20 06:51:55
0 2024/07/20 06:51:50
0 2024/07/20 06:51:44
I used the 2nd gen fan shroud, which was broken on the bottom, and did some more trimming to fit the non IC fan behind the new rad from Slaughter Zone.
I used the 2nd gen fan shroud, which was broken on the bottom, and did some more trimming to fit the non IC fan behind the new rad from Slaughter Zone.
0 2024/07/20 06:51:39