Dodge Diesel - Diesel Truck Resource Forums - Search Results

 
Search: Posts Made By: Crimedog
Showing results 1 to 25 of 500
Search took 0.06 seconds.
11-16-2018, 08:59 AM
Replies: 2
Views: 1,402
Posted By Crimedog

You only need a power and a ground to get the...

You only need a power and a ground to get the power movement of the seat. I swapped MY 2015 seats into a MY 2012 and the plugs were different, so we just jumpered the power and the ground and taped...
11-07-2017, 12:37 PM
Replies: 2
Views: 1,838
Posted By Crimedog

Most air bags seem to run 2-3 ohms resistance. ...

Most air bags seem to run 2-3 ohms resistance. Before making a permanent connection you could try sticking the resistor leads into the seat plug and turn the key on. If the resistance is right the...
08-08-2009, 12:30 AM
Replies: 98
Views: 16,336
Posted By Crimedog

Any updates on the truck? Hope it's still coming...

Any updates on the truck? Hope it's still coming together smoothly!
06-24-2009, 11:24 PM
Replies: 4
Views: 1,673
Posted By Crimedog

I think that somewhere around the 99 model year...

I think that somewhere around the 99 model year they changed the bolt sizes of the bushings, it looks like if his arms are built to spec that you ended up on the wrong side of the spec... Would it...
05-08-2009, 01:41 PM
Replies: 2
Views: 590
Posted By Crimedog

Dave, Check your speedometer sensor and see if...

Dave,
Check your speedometer sensor and see if it is installed 180* off. I pulled mine out before and couldn't remember how it went in so I guessed and I had the same thing as you - no speedo. So...
04-26-2009, 12:34 AM
Replies: 7
Views: 974
Posted By Crimedog

Was the crank scored or nicked at all? Any...

Was the crank scored or nicked at all? Any imperfections on the crank sealing surface will cause the seal to leak. Also, did you use the installation tool that came with the seal? Lastly, was the...
04-25-2009, 06:44 PM
Replies: 98
Views: 16,336
Posted By Crimedog

Just when I thought this thread couldn't get any...

Just when I thought this thread couldn't get any better, you show us this :)
04-21-2009, 11:17 PM
Replies: 18
Views: 1,364
Posted By Crimedog

Are you getting lots of smoke or no smoke at all?...

Are you getting lots of smoke or no smoke at all? I wonder if maybe wire brushing the injectors may have scarred a few holes or possibly plugged them up?
04-14-2009, 09:43 PM
Replies: 98
Views: 16,336
Posted By Crimedog

NICE WORK! Those aluminum pieces really turned...

NICE WORK! Those aluminum pieces really turned out great.

This is definitely one of my favorite threads to follow over the last couple of months. There's a lot of us that can't wait to see the...
04-13-2009, 09:15 PM
Replies: 16
Views: 1,595
Posted By Crimedog

If you have the switch in lockup position and hit...

If you have the switch in lockup position and hit the OD button, it will shift from 4th to 3rd while still locked up. Same goes for the other way (3rd to 4th).

However, if you're towing heavy I...
04-10-2009, 01:17 PM
Replies: 7
Views: 2,234
Posted By Crimedog

Similar, but not quite. I was going to do that,...

Similar, but not quite. I was going to do that, but the drawback is that you lose all the "automatic functions" of the automatic transmission. From what I gather, that just fools the PCM into...
04-09-2009, 08:14 PM
Replies: 4
Views: 898
Posted By Crimedog

DSS was the original acronym for "Darin's...

DSS was the original acronym for "Darin's Steering Stabilizer". It is a brace that supports the sector shaft of the steering box by placing a pillow block bearing on the lower part of the shaft. If...
04-09-2009, 08:07 PM
Replies: 7
Views: 2,234
Posted By Crimedog

Infidel, I think he's talking about the reprogram...

Infidel, I think he's talking about the reprogram that the dealer can supposedly do to delay the lockup until 50 mph. From what I've read the '94 pcms can't be reprogrammed, hence the need for a new...
04-07-2009, 08:33 PM
Replies: 12
Views: 809
Posted By Crimedog

Some guys have reported success by dropping the...

Some guys have reported success by dropping the pan down as much as possible, then pulling/cutting the old gasket out. Then to install the new one they put a clean slice in the gasket between two...
04-06-2009, 09:52 PM
Replies: 10
Views: 21,184
Posted By Crimedog

HotRodTodd, No need for a pic as there are...

HotRodTodd,
No need for a pic as there are plenty in my provided link. I guess when I think of circuit board, I think of a green PCB complete with resistors, capicitors, ICs, etc. When I did one...
04-05-2009, 07:17 PM
Replies: 7
Views: 2,105
Posted By Crimedog

Gotta love the soot spots! I get them with snow...

Gotta love the soot spots! I get them with snow and rain... and so do the cars next to me [tapdshut] I just built a set of vinyl covers for mine that have an elastic fit so they don't blow off. I...
04-05-2009, 07:07 PM
Replies: 10
Views: 21,184
Posted By Crimedog

Unless my eyes deceive me, there is only a...

Unless my eyes deceive me, there is only a potentiometer inside on the sending unit, no circuit board to worry about. It basically just sends a varying voltage to the truck's computer, and goes to...
04-05-2009, 01:49 PM
Replies: 4
Views: 502
Posted By Crimedog

My bad, I was under the impression you had an...

My bad, I was under the impression you had an analog gauge. Sounds like it very well could be the thermocouple then.
04-05-2009, 12:47 AM
Replies: 4
Views: 502
Posted By Crimedog

First check all of your wiring connections. Is...

First check all of your wiring connections. Is the needle sparatic or just slowly sweeping? I've had both, the sparratic movement was caused by a thermocouple wire cutting through the insulation...
04-04-2009, 08:35 PM
Replies: 4
Views: 900
Posted By Crimedog

From your picture, the other piece looks like...

From your picture, the other piece looks like part of the large snap ring that is used to hold the frictions & steels in place, possibly from the front drum. It was hard to get an idea of how long...
04-04-2009, 08:00 PM
Replies: 12
Views: 1,080
Posted By Crimedog

Has anybody had any luck with the electronic...

Has anybody had any luck with the electronic versions on ebay? For how cheap they are I figure they either don't have very good information or they're all pirated...
04-04-2009, 07:37 PM
Replies: 45
Views: 24,916
Posted By Crimedog

Just wondering if anyone has used the Isky cutter...

Just wondering if anyone has used the Isky cutter yet? Did it turn out?
04-04-2009, 05:01 PM
Replies: 12
Views: 747
Posted By Crimedog

Interesting info jfaulkner, it would be...

Interesting info jfaulkner, it would be interesting to see the breakdown on all the other cars and trucks. Definitely wasn't expecting the stats on the Sienna!
04-04-2009, 12:08 PM
Replies: 12
Views: 747
Posted By Crimedog

Are we talking US made or US assembled? Those...

Are we talking US made or US assembled? Those cars might be assembled here, but I'd be willing to guess that they have a lot more foreign parts on them than the Big 3. You have to remember that the...
04-02-2009, 07:59 PM
Replies: 11
Views: 17,927
Posted By Crimedog

Nope, doesn't hurt to drive with it like that. ...

Nope, doesn't hurt to drive with it like that. Mine have been shot for a while now, but I being a college kid I can put up with the little bit of noise they make until I can prioritize some funds...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.