Dodge Diesel - Diesel Truck Resource Forums - Search Results

Search: Posts Made By: gorms
Showing results 1 to 18 of 18
Search took 0.00 seconds.
11-11-2018, 08:44 PM
Replies: 2
Views: 208
Posted By gorms

It is also likely to just deform the seal...

It is also likely to just deform the seal temporarily, sometimes the leak will slow down or stop all together after a while.
10-23-2018, 09:29 AM
Replies: 6
Views: 328
Posted By gorms

Heater grid cycling, pretty sure there's a sticky...

Heater grid cycling, pretty sure there's a sticky on one of these 2nd gen pages. Its normal.
10-02-2018, 09:20 PM
Replies: 2
Views: 425
Posted By gorms

I've always been a fan of no fuel plate, not that...

I've always been a fan of no fuel plate, not that it helps you much!
Patience with tuning is critical to clean up the coal. I think I am running one of the old governor springs for an AFC spring and...
08-13-2018, 11:34 PM
Replies: 29
Views: 916
Posted By gorms

Well the plan is to have it ready for some sled...

Well the plan is to have it ready for some sled pulling fun this weekend, Ill keep you updated.
08-13-2018, 10:48 PM
Replies: 29
Views: 916
Posted By gorms

Heim joints from tractor supply, cat 1 top links...

Heim joints from tractor supply, cat 1 top links for 3 point hitch. They were about $20 each and about 2' long completely retracted. 3/4 mounting eye, cat 2 and 3 seemed to have larger mounting eye...
08-12-2018, 10:06 PM
Replies: 7
Views: 642
Posted By gorms

If I remember right, I was able to bar the motor...

If I remember right, I was able to bar the motor over with the alternator (or one crank bolt) with one hand and pull the timing plug out to feel for the notch with my other hand at the same time....
01-23-2018, 09:22 AM
Replies: 4
Views: 827
Posted By gorms

I would rather a high mileage original built...

I would rather a high mileage original built Cummins motor than a random builders rebuild.
01-22-2018, 08:55 PM
Replies: 4
Views: 827
Posted By gorms

Around here a fully dressed 12V goes for no more...

Around here a fully dressed 12V goes for no more than $1500-2000, with more than 15k miles obviously. I would be checking the ID tag and looking the block over to make sure it is a storm block, as...
12-04-2017, 08:59 PM
Replies: 12
Views: 1,567
Posted By gorms

Double check fuse in the left dash fuse box...

Double check fuse in the left dash fuse box marked IOD may have a funny little cover on it.
10-08-2017, 10:13 PM
Replies: 7
Views: 419
Posted By gorms

Two things I would look at before replacing parts...

Two things I would look at before replacing parts is the harness underthe steering column, they are known for breaking wires especially if you use the tilt a lot. I have also seen more than once the...
08-20-2017, 10:36 PM
Replies: 6
Views: 426
Posted By gorms

Quad 4x4 (torque king) describes the different...

Quad 4x4 (torque king) describes the different types of slip joints dodge used through the years. Slip yokes (http://www.quad4x4.com/catalog/category/dodge94-02frontdriveshaft2500-3500#cat_1419)
08-16-2017, 08:26 PM
Replies: 10
Views: 605
Posted By gorms

Without replacing the entire connector, you need...

Without replacing the entire connector, you need to find the other side of that connection, cut it off of the connector and do a permanent repair. Don't bother with a spade connector...they are not...
04-16-2017, 08:29 PM
Replies: 12
Views: 508
Posted By gorms

If your egt is accurate and downstream of the...

If your egt is accurate and downstream of the turbo reading 13-1400 you are waiting for melt down. I would start by checking for boost leaks. Then maybe install a boost elbow.

Black smoke is...
Replies: 1
Views: 1,579
Posted By gorms

Just my opinion here.... If you are good with...

Just my opinion here....
If you are good with maintenance and do your own work, diesels generally aren't too bad to keep up with, price wise. Then again I know some people that don't open their own...
02-14-2017, 09:06 AM
Replies: 12
Views: 818
Posted By gorms

As for vibration, if you separated the 2 piece...

As for vibration, if you separated the 2 piece driveshaft, the splines are keyed but 180* apart. Meaning they can go back together 2 ways.....the way it was balanced at the factory and 180* apart.
12-03-2016, 05:53 PM
Replies: 5
Views: 529
Posted By gorms

Hub bearing took a dump, most likely. Or your...

Hub bearing took a dump, most likely. Or your ball joints are really bad, with the wheels off the ground see where there is any play. Just up and down would be ball joints, as all directions would be...
05-17-2016, 09:13 PM
Replies: 4
Views: 846
Posted By gorms

AAMCO isn't going to be "cheap", just less than a...

AAMCO isn't going to be "cheap", just less than a quality rebuild. Price and quality. Go with someone reputable!
03-09-2016, 08:19 PM
Replies: 6
Views: 2,901
Posted By gorms

If it happens again before you get to look at it,...

If it happens again before you get to look at it, leave the key on (don't try to start again) and go see if the plunger on the shut down solenoid is all the way up. If it fell down, raise it with...
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.