GADTR#40 - North Georgia DTR
Registered User
Joined: Jun 2005
Posts: 74
Likes: 0
From: alpharetta georgia
on another note, i have been talking to a few guys and they are wanting to get a dodge truck meet going, and they are all for it, i know that at the same time id like to get a diesel meet going 1st, but im always down for anything...
we have pretty much come to the conclusion that sundays are for the most part best for every1 either that or maybe a saturday evening so maybe we can go have a few brewskis
anyways let me know what you guys think...
chris
we have pretty much come to the conclusion that sundays are for the most part best for every1 either that or maybe a saturday evening so maybe we can go have a few brewskis
anyways let me know what you guys think...
chris
Registered User
Joined: Jun 2007
Posts: 201
Likes: 0
From: Canton, GA
Hey guys, sorry I haven't gotten to a meet yet but I plan on it as soon as time permits.
Anyway, I'm getting rid of a bunch of stuff in the garage before I move to Macon, so check it out.
https://www.dieseltruckresource.com/...0&ppuser=55474
When's the next meet? Anywhere closer than kennesaw?
Anyway, I'm getting rid of a bunch of stuff in the garage before I move to Macon, so check it out.
https://www.dieseltruckresource.com/...0&ppuser=55474
When's the next meet? Anywhere closer than kennesaw?
Chapter President
Joined: Nov 2005
Posts: 356
Likes: 0
From: Dallas, GA
Chris, that is definatly a load bearing wall.. You can build a header or add a laminated beam depending on the span/length. It is holding the center of the second floor, floor joyces .
Len
Len
Registered User
Joined: Dec 2006
Posts: 220
Likes: 0
From: smokin the moutains of northeast Ga
depending on the span say 20 ft or less you can sandwich 2- 10"lvls with a piece of 3/8 ths plate in between and have no problems. It will cost you between $800- 1000 for the material. and a case of beer for your buddies to come help because the plate wil be heavy
Chapter President
Joined: Nov 2005
Posts: 356
Likes: 0
From: Dallas, GA
Hey Hippie, nice to have you join in our forum. Where about in the Mts of N. east Ga are you? May see you out and about one day. We will ba having a meet soon. Most folks are getting busy as the holidays are appraoching. First week of Nov. may work for everyone.
Len
Len
Registered User
Joined: Feb 2007
Posts: 140
Likes: 0
From: powder springs, GA
hey guys, sorry i havnt been on in awhile. ive been trying to buy a toyota buggy since i sold my jeep.
dyno day sounds good, about how much would it cost us to have one?
and a meeting the first of nov will not work for me, taking the buggy down to river rock for the weekend. but dont cancel cause of me tho, im sure ill be informed on the next one.
dyno day sounds good, about how much would it cost us to have one?
and a meeting the first of nov will not work for me, taking the buggy down to river rock for the weekend. but dont cancel cause of me tho, im sure ill be informed on the next one.
Registered User
Joined: Dec 2006
Posts: 220
Likes: 0
From: smokin the moutains of northeast Ga
Registered User
Joined: May 2006
Posts: 253
Likes: 0
From: Canton, Georgia
Hi Guys,
Apologies for not being at wrench night. My hand is healing nicely. I am very inerested in a Dyno day; however, My clutch is on its last leg and slips badly in 3rd and 4th when I get into the skinny pedal. Therefore I probably wouldn't get an accurate reading until I replace it.
Len and everyone else, I am considering a Sachs 13 inch double disc. Do you think this is overkill and Len do you rent transmission jacks? I have been told that the Getrag and the NP205 can be removed together by just removing the bolts that attach the tranny to the bell housing. If this is the case I am considering replacing the clutch myself.
What do you guys think, reccomend, etc...?
Joseph
Apologies for not being at wrench night. My hand is healing nicely. I am very inerested in a Dyno day; however, My clutch is on its last leg and slips badly in 3rd and 4th when I get into the skinny pedal. Therefore I probably wouldn't get an accurate reading until I replace it.
Len and everyone else, I am considering a Sachs 13 inch double disc. Do you think this is overkill and Len do you rent transmission jacks? I have been told that the Getrag and the NP205 can be removed together by just removing the bolts that attach the tranny to the bell housing. If this is the case I am considering replacing the clutch myself.
What do you guys think, reccomend, etc...?
Joseph
Chapter President
Joined: Nov 2005
Posts: 356
Likes: 0
From: Dallas, GA
Joseph, glad your hand is healing well. That clutch might be a footfull for everyday driving: 13disc. Better ask in the 1st gen and see what others chime in with. Been a while since I've had to drive a hand shaker in a 3/4 ton truck. I do not have tranny jacks for rent. I do have regular floor jacks that you may be able to adapt with straps. I did when pulling out my tranny from my cj-7 and it worked O.K.
Len
Len
Chapter President
Joined: Nov 2005
Posts: 356
Likes: 0
From: Dallas, GA
Mike at Mr. tranny over on hwy140 going towards Waleska. He is the owner.
his shop is 1 mile North on 140 past the YMCA in Canton. If you want to set something up I will meet you up at his shop and talk him into some kind of discount for you.. Mike is pretty cool and knows his stuff...
Len
his shop is 1 mile North on 140 past the YMCA in Canton. If you want to set something up I will meet you up at his shop and talk him into some kind of discount for you.. Mike is pretty cool and knows his stuff...
Len
Registered User
Joined: May 2006
Posts: 253
Likes: 0
From: Canton, Georgia
I hope to receive my Con OFE 13" clutch from South Bend Clutch today, that baby was not cheap. I went to Harbor freight yesterday and purchased a HD 3 ton floor jack, 6 ton jack stands, a transmission adapter to go on the 3 ton jack, and a creeper for me to ease things. I have a buddy coming up from Savannah next week and hope to save a few bucks by installing it ourselves. Wish me luck.
Joseph
Joseph
