Dodge Diesel - Diesel Truck Resource Forums

1st Gen. Ram - All Topics Discussion for all Dodge Rams prior to 1994. This includes engine, drivetrain and non-drivetrain discussions. Anything prior to 1994 should go in here.

Fuel Pump turn up

   
Old Jan 4, 2011 | 02:54 PM
Share
  #31  
Farmboy12357's Avatar
Farmboy12357
Thread Starter
Registered User
 
Joined: Dec 2010
Posts: 284
Likes: 0
From: Nampa, ID
What's the l/h side? and PCM? sorry again for the dumb question. the Boise Area
Reply
0
Old Jan 4, 2011 | 03:01 PM
Share
  #32  
huntinguy's Avatar
huntinguy
Registered User
 
Joined: Dec 2009
Posts: 321
Likes: 0
Left hand side. And power train control module.
Reply
0
Old Jan 4, 2011 | 03:01 PM
Share
  #33  
raggmann's Avatar
raggmann
Registered User
 
Joined: Nov 2006
Posts: 351
Likes: 0
From: Botha,Alberta,Canada
l/h-left hand
PCM -basically the computer inside the l/h fender beside the battery,behind the headlight.
Reply
0
Old Jan 4, 2011 | 03:04 PM
Share
  #34  
Farmboy12357's Avatar
Farmboy12357
Thread Starter
Registered User
 
Joined: Dec 2010
Posts: 284
Likes: 0
From: Nampa, ID
yeah, I figured it meant left hand about a second after i hit reply. ok, i'll go look for it
Reply
0
Old Jan 4, 2011 | 03:14 PM
Share
  #35  
Farmboy12357's Avatar
Farmboy12357
Thread Starter
Registered User
 
Joined: Dec 2010
Posts: 284
Likes: 0
From: Nampa, ID
When you say the "3-wire plug", is it under the dash or under the hood?
Reply
0
Old Jan 4, 2011 | 03:28 PM
Share
  #36  
Farmboy12357's Avatar
Farmboy12357
Thread Starter
Registered User
 
Joined: Dec 2010
Posts: 284
Likes: 0
From: Nampa, ID
ok, I think all the connections are good. I think I just need to replace the Magnets or whatever sensor is on the engine. How do I go about getting to that and replacing it?
Reply
0
Old Jan 4, 2011 | 03:39 PM
Share
  #37  
raggmann's Avatar
raggmann
Registered User
 
Joined: Nov 2006
Posts: 351
Likes: 0
From: Botha,Alberta,Canada
The 3 wire plug is indide the cab.
As far as the pick-up magnets or whatever.....I'm not sure.
Reply
0
Old Jan 4, 2011 | 03:41 PM
Share
  #38  
Farmboy12357's Avatar
Farmboy12357
Thread Starter
Registered User
 
Joined: Dec 2010
Posts: 284
Likes: 0
From: Nampa, ID
okay, I can't find the 3 wire plug but all the wires that come off the tach seem to attach to somewhere. I think it's just the magnet pick ups
Reply
0
Old Jan 4, 2011 | 03:42 PM
Share
  #39  
huntinguy's Avatar
huntinguy
Registered User
 
Joined: Dec 2009
Posts: 321
Likes: 0
Your truck will have a CPS crank shaft positoning sensor.
Reply
0
Old Jan 4, 2011 | 03:43 PM
Share
  #40  
Farmboy12357's Avatar
Farmboy12357
Thread Starter
Registered User
 
Joined: Dec 2010
Posts: 284
Likes: 0
From: Nampa, ID
Where do I find that? I don't know what it looks like
Reply
0
Old Jan 4, 2011 | 03:45 PM
Share
  #41  
huntinguy's Avatar
huntinguy
Registered User
 
Joined: Dec 2009
Posts: 321
Likes: 0
Don't Know my truck doesn't have one.
Reply
0
Old Jan 4, 2011 | 03:48 PM
Share
  #42  
Farmboy12357's Avatar
Farmboy12357
Thread Starter
Registered User
 
Joined: Dec 2010
Posts: 284
Likes: 0
From: Nampa, ID
okay
Reply
0
Old Jan 4, 2011 | 03:58 PM
Share
  #43  
huntinguy's Avatar
huntinguy
Registered User
 
Joined: Dec 2009
Posts: 321
Likes: 0
I went out to my other truck and found it. It's right betwein the water pump and the crank pully.
Reply
0
Old Jan 4, 2011 | 04:01 PM
Share
  #44  
JBradley500's Avatar
JBradley500
Registered User
 
Joined: Feb 2010
Posts: 1,044
Likes: 1
From: A 5th dimension, beyond that which is known to man.
.049" gap (plus or minus a couple thou) should be between the sensor and the pulley... might want to check your if its not working.
Reply
0
Old Jan 4, 2011 | 04:05 PM
Share
  #45  
Farmboy12357's Avatar
Farmboy12357
Thread Starter
Registered User
 
Joined: Dec 2010
Posts: 284
Likes: 0
From: Nampa, ID
is it on the side of the engine and what's it look like?
Reply
0

Thread Tools
Search this Thread
Search this Thread:

Advanced Search

Advanced Search

All times are GMT -5. The time now is 12:17 AM.