Dodge Diesel - Diesel Truck Resource Forums

 
Page 1 of 3
1
2
3
Search: Posts Made By: pocketchange
Showing results 1 to 25 of 71
Search took 0.03 seconds.
Forum: Towing and Hauling / RV
04-09-2013, 06:15 PM
Replies: 6
Views: 4,023
Posted By pocketchange

If I had to do this again, I WOULD NOT do it with...

If I had to do this again, I WOULD NOT do it with a 1 Ton and a float. The single axle is a much better and much cheaper path to follow.

DO NOT QUIT YOUR DAY JOB...!!
Forum: Towing and Hauling / RV
04-09-2013, 06:01 PM
Replies: 21
Views: 3,611
Posted By pocketchange

I run an AirHitch Divider with my minifloat and...

I run an AirHitch Divider with my minifloat and Firestone bags on the diff. at a 2/1 ratio and my rig rides like a lemo.

If you are not allowing your suspension to handle the larger
portion of...
Forum: Towing and Hauling / RV
04-09-2013, 05:42 PM
Replies: 28
Views: 151,359
Posted By pocketchange

Just came across this thread.. interesting. ...

Just came across this thread.. interesting.

I heavy haul ALL the time and gross upwards of 35/36K and 20K empty.
The only way to get any mileage from a brake system is to maintain the entire...
Forum: 24 Valve Engine and Drivetrain
10-20-2012, 09:24 AM
Replies: 1
Views: 2,128
Posted By pocketchange

As much as you don't care for the automatic, I'd...

As much as you don't care for the automatic, I'd stick with it.
Finding (decent) hard parts for the NV5600 is a PITA.
Forum: 1st Gen. Ram - All Topics
11-20-2011, 10:01 PM
Replies: 12
Views: 37,668
Posted By pocketchange

What?

With these torque procedure(s) coming from locations other than DANA,
here is what was suggested (to me).

Spinning the freshly assembled hub (assuming it's done correctly).
Torque to 70 ft...
Forum: 3rd Gen Engine and Drivetrain -> 2003-2007
11-10-2011, 05:15 PM
Replies: 49
Views: 190,468
Posted By pocketchange

A few suggestions..

Replace/re-install the bearings with a NEW nut and the balance of the hardware..
DO NOT RE-USE THE OLD HARDWARE that tighten the bearing pack.
DO NOT have any slack in the bearings. ANY play is...
Forum: Performance and Accessories 2nd gen only
12-05-2010, 01:43 PM
Replies: 10
Views: 2,230
Posted By pocketchange

so.. what did the Edge folks have to say?

After 300K plus miles, mine tossed a p1960 code and acting strangely.
I couldn't find any pump issues or other problems.
Pulled the Edge EZ out of the loop and it hasn't missed a lick since. ...
Forum: 24 Valve Engine and Drivetrain
08-08-2010, 02:40 PM
Replies: 71
Views: 6,327
Posted By pocketchange

Does not Vulcan have the re-wire harness kit for...

Does not Vulcan have the re-wire harness kit for less than $20 to get the ladies in-tank pump working? I ask this in lieu of Vulcan selling a In-tank upgrade that looks to be nearly identical to the...
Forum: 24 Valve Engine and Drivetrain
07-29-2010, 01:17 PM
Replies: 6
Views: 9,375
Posted By pocketchange

After 300K Plus & excess blow-by since I drove it...

After 300K Plus & excess blow-by since I drove it new off the lot, I rebuilt the head.
Interesting that Cummins decided to forego using guides.
Replaced the valves, added guides, Fel-Pro Head...
Forum: 24 Valve Engine and Drivetrain
03-15-2007, 09:00 AM
Replies: 4
Views: 705
Posted By pocketchange

Mag cover operation may have the adapter you...

Mag cover operation may have the adapter you need, give'm a call.
Forum: 24 Valve Engine and Drivetrain
03-13-2007, 10:15 PM
Replies: 19
Views: 2,339
Posted By pocketchange

ALSO: If you have a trailer and use...

ALSO:
If you have a trailer and use vacumn/hyd brakes (with a booster) the pump works harder, creating ... more blowby.
Pump the brakes, see the blowby.
Let the vacumn reserve build back...
Forum: 24 Valve Engine and Drivetrain
03-13-2007, 09:37 PM
Replies: 4
Views: 705
Posted By pocketchange

Check your Vin # for posi info. As for Gear...

Check your Vin # for posi info.
As for Gear Lube: LubeMaster (800 527 9929) ask For Rick Martinez.
It ain't cheap, but the best never is.
The ligher weight should work with no problem and the...
Forum: 24 Valve Engine and Drivetrain
03-13-2007, 09:26 PM
Replies: 21
Views: 1,664
Posted By pocketchange

Get A 6er with the tall gear set. I pull up to...

Get A 6er with the tall gear set. I pull up to 36K all over the US with no problem.
11/12 MPG @ 1800 @ 65MPH. Don't get in a rush (unless necessary) to save
fuel...!

Second SB FE O @ 135K...
Forum: 24 Valve Engine and Drivetrain
03-04-2007, 07:29 AM
Replies: 58
Views: 389,925
Posted By pocketchange

wadecool, Exactly... my dead pedal condition...

wadecool,
Exactly... my dead pedal condition is to the point of being predictable.
When this pedal codition started I was more than a little upset but after some time I got used to it (in lieu...
Forum: 24 Valve Engine and Drivetrain
03-03-2007, 09:29 AM
Replies: 3
Views: 2,684
Posted By pocketchange

Call Southern Plains in Dallas. No questions...

Call Southern Plains in Dallas.
No questions asked, great service and quick shipping.
(i got two) sold one and installed the other till get inspired and mount the
Glacier Kit.
Forum: 24 Valve Engine and Drivetrain
03-03-2007, 09:24 AM
Replies: 4
Views: 814
Posted By pocketchange

With that many miles, why not rebuild it. It...

With that many miles, why not rebuild it. It would be cheaper in the long run.
I've done mine @ every 100K and keep a spare, junk yard is a good source.
Keeping track of COLD battery voltage is a...
Forum: 24 Valve Engine and Drivetrain
03-03-2007, 09:07 AM
Replies: 13
Views: 1,944
Posted By pocketchange

If you have a blown seal in the turbo it could be...

If you have a blown seal in the turbo it could be the problem. Especially if the previous owner failed regular fitler changes, shut down too soon (hot), etc. Turbos are tough but not bullet proof...
Forum: 24 Valve Engine and Drivetrain
03-03-2007, 08:36 AM
Replies: 58
Views: 389,925
Posted By pocketchange

When mine goes to (idle) dead pedal, I pedal the...

When mine goes to (idle) dead pedal, I pedal the throttle a few times and off we go. Softly by the way (PLEASE).
I was told I needed a new VP44... what?
Other than a dead pedal IT IS RUNNING...
Forum: 24 Valve Engine and Drivetrain
03-03-2007, 07:45 AM
Replies: 65
Views: 12,382
Posted By pocketchange

Cup Holders ? ***..!

Me thinks 12 Valve was interested in which 24 valve engine...?

I've got an 01' with 265K Plus... Very Hard miles and nothing but
a smile on my face... Too bad I can't say the same for the 03'...
Forum: 24 Valve Engine and Drivetrain
02-26-2007, 09:19 AM
Replies: 32
Views: 52,463
Posted By pocketchange

Expense aside, not using the available and top of...

Expense aside, not using the available and top of the line hard parts in a driveline rebuild is looking for trouble.
Start with replacing the rear main, the Cummins seal is the best bet.
Broach the...
Forum: 24 Valve Engine and Drivetrain
02-22-2007, 02:39 PM
Replies: 62
Views: 7,846
Posted By pocketchange

That's RIGHT

Dodge and CO., have no problem leaving their customer base in the grease.

The LP campaign program should be offered to everyone having this problem.
I opted for the Glacier Fix after due...
Forum: 24 Valve Engine and Drivetrain
02-22-2007, 01:59 PM
Replies: 4
Views: 572
Posted By pocketchange

I've got a load of miles on mine and no oil...

I've got a load of miles on mine and no oil traces on the air horn.
If it's a new buy, maybe you need to visit the seller with this situation and see what they have to offer.
Forum: 24 Valve Engine and Drivetrain
02-22-2007, 12:37 PM
Replies: 2
Views: 2,185
Posted By pocketchange

I've been happy with the hub located shot filled...

I've been happy with the hub located shot filled O-Rings. I've had them for what seems like decades (it has been decades). Last time I checked they were $100 per. My last set of Mich's lasted 115K...
Forum: 24 Valve Engine and Drivetrain
02-22-2007, 12:29 PM
Replies: 9
Views: 1,035
Posted By pocketchange

I'm headed to the scrap yard to find an old Ford...

I'm headed to the scrap yard to find an old Ford washer bottle with the built in mounting bracket and raiding the bathroom for something to suck up the oil
(Kotex maybe). I'm tired of living with...
Forum: 24 Valve Engine and Drivetrain
02-22-2007, 12:17 PM
Replies: 62
Views: 7,846
Posted By pocketchange

Vulcan Kit is a good fix, Glacier 391 has a...

Vulcan Kit is a good fix, Glacier 391 has a better fix (and ends the VP44 worry). Add (any) other kits you care to at this point.
If you don't have a fuel pressure guage of some sort, SHAME ON YOU....
Showing results 1 to 25 of 71
 
Page 1 of 3
1
2
3


 
Forum Jump


All times are GMT -5. The time now is 12:22 PM.