Washed 'er up, and took the pipe organs off.
#1
Washed 'er up, and took the pipe organs off.
Washed up the ole girl.
Took off the pipe organ stacks, 4 4" stacks..
And put a single 5" out the side for now.
I like the way it turned out, and the way it sounds!
I also put interior out of a 99 I think in, and new headliner..
heres some pictures!
Took off the pipe organ stacks, 4 4" stacks..
And put a single 5" out the side for now.
I like the way it turned out, and the way it sounds!
I also put interior out of a 99 I think in, and new headliner..
heres some pictures!
#5
Nice job on the interior, and exhaust. Truck looks much better now, especially the inside. I am taking my stacks off this weekend, I really like them but they are just to loud for the amount of driving I do.
Any fab work involved in the seat/door panels or was it a straight forward swap?
Any fab work involved in the seat/door panels or was it a straight forward swap?
#6
Registered User
Join Date: Mar 2004
Location: Austin, TX, Toronto, ON
Posts: 1,488
Likes: 0
Received 0 Likes
on
0 Posts
good job!...im thinking about gettign the stacks down this summer too...i take alot of big long hour trips and it gets fatiguing aftre a few hours of straight driving...thinking about putting the old 3inch exhaust back on and adding a 5 inch pipe from the rear axle back...that way no drone in the cab and still sound mean...i do like the creativity of the pipe organ stacks...did u get that idea of pimp my truck? i saw it there..pretty neat
Trending Topics
#8
Registered User
Join Date: Jun 2004
Location: SunnyVale Trailer Park
Posts: 1,668
Likes: 0
Received 0 Likes
on
0 Posts
Nice lookin truck
[quote=mr T;1474845thinking about putting the old 3inch exhaust back on and adding a 5 inch pipe from the rear axle back...that way no drone in the cab and still sound mean[/quote]
I don't have any drone at all below 130 km/h , if you need to travel faster than that , then you need an airplane. I have a 4" down pipe and 5" straight to the back corner.
[quote=mr T;1474845thinking about putting the old 3inch exhaust back on and adding a 5 inch pipe from the rear axle back...that way no drone in the cab and still sound mean[/quote]
I don't have any drone at all below 130 km/h , if you need to travel faster than that , then you need an airplane. I have a 4" down pipe and 5" straight to the back corner.
#9
Nice job on the interior, and exhaust. Truck looks much better now, especially the inside. I am taking my stacks off this weekend, I really like them but they are just to loud for the amount of driving I do.
Any fab work involved in the seat/door panels or was it a straight forward swap?
Any fab work involved in the seat/door panels or was it a straight forward swap?
I figured I'd be able to use the mounts off the old seats and mount the new seats on the old mount.
But the back part of the seat is built into the new mount so all I would of been able to remove is the bottem (where your butt sits).
So there it added about 4" to height, and there is a 4" gap for the front bolts that I'm going to get a tube and put between the mount/floor w/ a washer on each end and put a longer bolt down through.
As the panals go, once again the switches had to be changed, and the doors on the truck I got it off of where squared at the bottem corner so I had to saw off a little bit to get them to close, and im going to fiberglass it. And paint it to match.
I got the nerfbars, for $30 bucks, both of them, they retail for like $200 new.
I got the seats, two headlight buckets, headliner for $100 bucks off of a local guy who rebuilds cars n sells them.
All the local junk yards wanted $150.00 just for a seat .
Now all I need is to finish up the interior, get my CD deck in there, get my trailer tow mirors, and put my speakers in and the inside should be good to go.
Thanks for all the positive comments!
#13
Registered User
Join Date: Jan 2007
Location: Salem,nh/Port Tampa,Fl
Posts: 686
Likes: 0
Received 0 Likes
on
0 Posts
OK... I want to under side ,side dumps like sidepipes...so are you selling the old ones or ....not ?
I was gonna do a 'T' and run stacks under the sides...to side dump..,Flip
I was gonna do a 'T' and run stacks under the sides...to side dump..,Flip
Thread
Thread Starter
Forum
Replies
Last Post
lovin1stgens
1st Gen. Ram - All Topics
70
03-19-2012 09:41 AM
jon05ctd
3rd Generation Ram - Non Drivetrain - All Years
13
12-25-2005 08:08 AM
passnu2
HELP!
20
12-19-2004 09:09 PM