New HTS Billet tranny tomorrow
10-11-2006, 09:38 PM
#1
Registered User
Thread Starter
Join Date: Jan 2006
Location: Statesboro, GA
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
New HTS Billet tranny tomorrow
Getting my new fully billet tranny
"except for output shaft,becuase no one has any in the nation darn'it"
Gonna try to get it installed by tomorrow and put some miles on real tranny think to dusty and mary ann at HTS
let ya no how that goes and when gets some miles on it show these georgia boy with there powerchokes and durapads what a real truck is
Now to firgure out what kind of turbo.......
"except for output shaft,becuase no one has any in the nation darn'it" Gonna try to get it installed by tomorrow and put some miles on real tranny think to dusty and mary ann at HTS
let ya no how that goes and when gets some miles on it show these georgia boy with there powerchokes and durapads what a real truck is Now to firgure out what kind of turbo.......
10-12-2006, 08:31 AM
#2
Registered User
Join Date: Jan 2004
Location: Maritimes, Canada
Posts: 2,696
Likes: 0
Received 0 Likes
on
0 Posts
Your gonna need some injectors and at least a 66 turbo to kick some serious tail...The turbo will get you most of the way there but the 03 stix are in need of a hone or ideally new flux nozzles to make the big power. On an 03 with a stock Cp3 550 with lots of air is a great number. The hottest 04.5 to 06's are making 660hp with big turbos, stix and a double or triple stack. Good luck. IF you don't mind a little smoke... an Aurora 5000 or K31 Hybrid is the biggest streetable turbo for big power. ks
10-12-2006, 09:28 AM
#4
Registered User
Join Date: Jun 2003
Location: FEDERAL WAY, WA
Posts: 297
Likes: 0
Received 0 Likes
on
0 Posts
10-12-2006, 02:58 PM
#5
Registered User
Join Date: Nov 2005
Location: New Braunfels, TX
Posts: 379
Likes: 0
Received 0 Likes
on
0 Posts
10-12-2006, 03:50 PM
#6
Registered User
Thread Starter
Join Date: Jan 2006
Location: Statesboro, GA
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
depends if it's a good buy Thanks for all the help guys and all help will be put ot thought because i need all the information i can get to make this thing to haul butt and as for the output shaft they just couldn't get one at the time and i was to impatient to wait so I'll just install it later if I need it. Thanks again guys
Thanks for all the help guys and all help will be put ot thought because i need all the information i can get to make this thing to haul butt and as for the output shaft they just couldn't get one at the time and i was to impatient to wait so I'll just install it later if I need it. Thanks again guys
Trending Topics
10-12-2006, 07:19 PM
#9
Registered User
Join Date: Feb 2004
Location: south west, Michigan
Posts: 629
Likes: 0
Received 0 Likes
on
0 Posts
You wont be disappointed with the HTS. Were going up tomorrow to see Dusty, Termite06 is getting a trans built and I have to fix a broken output shaft
Randy
Randy
10-12-2006, 07:29 PM
#10
Registered User
Join Date: Jan 2004
Location: Maritimes, Canada
Posts: 2,696
Likes: 0
Received 0 Likes
on
0 Posts
Output shafts are a nice relief valve.....The stock ones are $70 at my shop and only the overdrive section needs to be torn off. Unless you are really unlucky and you crack the OD housing or break the shaft in the Transfer case (4wd). 47re's tend to crack the OD housing....48re's have a better record so far.....maybe a billet OD housing is needed. ks
10-12-2006, 09:10 PM
#12
Registered User
Thread Starter
Join Date: Jan 2006
Location: Statesboro, GA
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
torque converter problem
the torque on my tranny want just slide in it went in about an inch when i tapped it with a rubber mallet "not real hard" but its like the torque converter shaft on the outside is to big for what seems to be a bushing maybe behind the front seal. Is this right to have to be so hard going in. Trying to get some help on this so I can get it half way installed tonight.
10-12-2006, 10:07 PM
#13
Registered User
Join Date: Jun 2003
Location: FEDERAL WAY, WA
Posts: 297
Likes: 0
Received 0 Likes
on
0 Posts
If your dealer is selling mine they are available. Part number and info is listed at http://www.opieparts.com/products.aspx
