How much HP do I have??
07-02-2009, 08:36 PM
#3
Registered User
Thread Starter
Join Date: Feb 2008
Location: Versailles Illinois
Posts: 330
Likes: 0
Received 0 Likes
on
0 Posts
Really dang, I was hoping closer to 400...What would you suggest to het to around 400.. and how much can i get with the stock Hy35....thanks Babyjoe.
07-02-2009, 08:52 PM
#4
Registered User
Join Date: Apr 2007
Location: SLC, Ut. 4,200 ft.
Posts: 990
Likes: 0
Received 0 Likes
on
0 Posts
Not very much. You could start by addin a j-hook or turn buckle to your waste gate. But anymore added fuel and youll want to start thinking about bigger turbo.
Trucks like mine and yours are stock with with about 215-225 at the fly wheel. That prob drops to 175ish rear wheelhp. So really, 325 isnt too bad for just havin intake filter, exhaust, chip, and mild sticks.
Im shootin for 450 rwhp and plannin on addin 100ish hp sticks and bigger turbo to get me there. Aslo Im at 4,500 ft though.
thats my .02. hope it helps
Trucks like mine and yours are stock with with about 215-225 at the fly wheel. That prob drops to 175ish rear wheelhp. So really, 325 isnt too bad for just havin intake filter, exhaust, chip, and mild sticks.
Im shootin for 450 rwhp and plannin on addin 100ish hp sticks and bigger turbo to get me there. Aslo Im at 4,500 ft though.
thats my .02. hope it helps
07-02-2009, 10:36 PM
#5
Registered User
Join Date: Jan 2005
Location: eastern pa
Posts: 915
Likes: 0
Received 0 Likes
on
0 Posts
Your more in the 350 or more range. You need a turbo upgrade and youll be in the 400area. A comp and built tranny will put you in the 310 320 range if your vp is strong.
07-03-2009, 04:08 PM
#6
Registered User
Join Date: Sep 2008
Location: Latham, Missouri and now Goshen, Indiana
Posts: 311
Likes: 0
Received 0 Likes
on
0 Posts
yup id say your 350 plus.. i seen a 02 dyno with a edge comp and a small turbo upgrade and he made 340. with the jammer injectors u should easy be at 350.
Trending Topics
07-07-2009, 08:34 PM
#8
Registered User
Thread Starter
Join Date: Feb 2008
Location: Versailles Illinois
Posts: 330
Likes: 0
Received 0 Likes
on
0 Posts
What turbo would you all recomend, I would like to be around 500-600 someday.I do have a brake spring off a semi holding my waste gate it works great. i have had some over boost codes with it so I am guessing it works good
, i need to take some pictures of it and post it in case someone else would like to do it.....cheap too...
, i need to take some pictures of it and post it in case someone else would like to do it.....cheap too...
07-07-2009, 09:46 PM
#9
Registered User
Join Date: Apr 2007
Location: SLC, Ut. 4,200 ft.
Posts: 990
Likes: 0
Received 0 Likes
on
0 Posts
HA hel yea! I wish I would've known what I was doin more when I bought my J-hook. Couldve made the same thing from home depot for 5 bucks.
But anyway, Id look into a 62/65/14 turbo. Maybe even 62/71/14 to keep temps cooler around 500+ hp. Im a fan of indusrtial injestion turbos.
Imsure youll get a few others pitchin in on this topic.
But anyway, Id look into a 62/65/14 turbo. Maybe even 62/71/14 to keep temps cooler around 500+ hp. Im a fan of indusrtial injestion turbos.
Imsure youll get a few others pitchin in on this topic.
07-07-2009, 10:13 PM
#10
Registered User
Thread Starter
Join Date: Feb 2008
Location: Versailles Illinois
Posts: 330
Likes: 0
Received 0 Likes
on
0 Posts
When it comes to turbo's I am kinda behind, What does all the 62/72/14 mean I know its size but is it millimeters. i will do some research it will be awhile before I buy any performance parts since I just purchased a tranny....
07-07-2009, 10:51 PM
#11
Chapter President
Join Date: Nov 2003
Location: Rural Hall, NC
Posts: 3,807
Likes: 0
Received 0 Likes
on
0 Posts
The 62mm is the inducer size of the compressor wheel, 72 is the exducer size of the turbine wheel. These are all just numbers that are part of a math formula to figure wheel trim.
The 14 is measured in cm which is how Holset measure their turbine housings. It's actually a .80 a/r by Borg Warner standards.
The 14 is measured in cm which is how Holset measure their turbine housings. It's actually a .80 a/r by Borg Warner standards.
Thread
Thread Starter
Forum
Replies
Last Post
jjrightmire1973
3rd Gen High Performance and Accessories (5.9L Only)
5
08-12-2008 04:29 PM
MR. GADGET
3rd Gen Engine and Drivetrain -> 2003-2007
5
04-24-2003 02:51 PM
GaCamper
12 Valve Engine and Drivetrain
7
02-04-2003 12:30 AM