MP8 & Quad Boost Fooler??
11-06-2009, 04:52 PM
#1
Registered User
Thread Starter
Join Date: Mar 2005
Location: Red Deer, Alberta
Posts: 3,190
Likes: 0
Received 0 Likes
on
0 Posts
MP8 & Quad Boost Fooler??
I'm going to be adding a TS MP8 to the mix and already have a Quad Boost Fooler. Can I run both or should I remove the Quad? Does the MP8 boost fool even if it is in the off or lowest position? Thanks for any ideas or tips...
11-07-2009, 02:14 AM
#6
Registered User
Join Date: Dec 2006
Location: Fresno, Ca
Posts: 842
Likes: 0
Received 0 Likes
on
0 Posts
as long as the mp8 is on at least 1%, it won't throw codes. When I have it all the way down, it will throw overboost codes. Ditch the quad, keep it above 1%.
-jp
-jp
11-07-2009, 11:07 AM
#7
Registered User
Thread Starter
Join Date: Mar 2005
Location: Red Deer, Alberta
Posts: 3,190
Likes: 0
Received 0 Likes
on
0 Posts
I guess that should be save for daily driving too? A guy should obviously run the Smarty TNT on stock rail pressure too??
Trending Topics
11-07-2009, 04:37 PM
#9
Registered User
Join Date: Dec 2006
Location: Fresno, Ca
Posts: 842
Likes: 0
Received 0 Likes
on
0 Posts
Get a rail pressure gauge. Keep it around 18-19k for extended periods of time (i.e. highway driving). With the smarty on stock rail pressure, you'll probably be somewhere around 10-30% on the mp8 to achieve this pressure.
11-07-2009, 10:03 PM
#10
Registered User
Thread Starter
Join Date: Mar 2005
Location: Red Deer, Alberta
Posts: 3,190
Likes: 0
Received 0 Likes
on
0 Posts
I have the Quad commander. My pressure is around 17k on the highway, 22k WOT and 6k idle on TNT #9
11-07-2009, 10:10 PM
#11
Registered User
Join Date: Feb 2009
Location: SoCal
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
It modifies the boost pressure signal to the ECM fooling it into thinking the pressure is lower and therefore the ECM allows you to make more boost. This gets you higher boost for very little money. I think you will need a separate boost gauge of some sort to see you actual pressure.
11-08-2009, 05:38 PM
#12
Registered User
Thread Starter
Join Date: Mar 2005
Location: Red Deer, Alberta
Posts: 3,190
Likes: 0
Received 0 Likes
on
0 Posts
With the MP8, where does a guy tap into for rail pressure? I'm tapped onto the blue wire at the plug now but do I now tap onto the blue wire on the MP8 side closest to the rail pressure sensor?
Thread
Thread Starter
Forum
Replies
Last Post
fullthrottle07
3rd Gen High Performance and Accessories (5.9L Only)
2
01-19-2008 12:09 AM
Rollin' Smoke
3rd Gen High Performance and Accessories (5.9L Only)
23
06-26-2007 09:04 PM
rkelley
3rd Gen High Performance and Accessories (5.9L Only)
19
01-11-2007 10:59 PM
973604x4
3rd Gen High Performance and Accessories (5.9L Only)
22
10-22-2006 09:08 PM
smoky beast
3rd Gen High Performance and Accessories (5.9L Only)
28
10-13-2006 01:15 PM
