Performance and Accessories 2nd gen only Talk about Dodge/Cummins aftermarket products for second generation trucks here. Can include high-performance mods, or general accessories.

injector install experts????

Thread Tools
 
Search this Thread
 
Old 06-07-2005, 09:46 PM
  #1  
Registered User
Thread Starter
 
caper's Avatar
 
Join Date: Dec 2004
Location: Cape Breton,N.S / Ft Mac AB
Posts: 611
Likes: 0
Received 1 Like on 1 Post
injector install experts????

Hi just installed 275s and wondering are the injectors suppose to slam in once they get to the o ring ?no amount of pushin with my thumb could get them down enough to get the keeper on so I used the handle of a hammer to apply a little more pressure on them and all of a sudden they would slam in hard the last cm or so. Is this normal???I,m sure I can hear the truck lope some times when pullin away or am I parionid. The keepers seemed to slide in easyer than they were to slide out , scared I may of scewed somethin up. Thanks
Old 06-07-2005, 10:28 PM
  #2  
Registered User
 
duallydave's Avatar
 
Join Date: Jan 2005
Location: vernon b.c. canada
Posts: 1,226
Likes: 0
Received 0 Likes on 0 Posts
Talking

sounds pretty normal,when i put mine in they to were hard the last little bit.didnt have to hit them with a hammer but sqished the thumb quite a bit.ive read the tourque should be just rite on them though.i didnt have a inch wrench so i guessed in comparing with the others.other than the hard install do you like the power?ive read the 275s give better milage.my 130hp sticks didnt give any better milage but not any worse though.
Old 06-07-2005, 11:15 PM
  #3  
Registered User
 
Hemi Cat's Avatar
 
Join Date: Nov 2004
Location: South Western New Mexico
Posts: 822
Likes: 0
Received 0 Likes on 0 Posts
Did you lube the "O" rings? I use silicone grease, Dow Corning 111. They slip right in with only a little resistance. When they push hard, you are stressing the O rings and can chaff, cut or roll them and have a leaker later on.
Old 06-08-2005, 05:33 AM
  #4  
Registered User
 
Jetpilot's Avatar
 
Join Date: Apr 2002
Location: Hershey, PA
Posts: 1,250
Likes: 0
Received 0 Likes on 0 Posts
Lube the o-rings and pull the injector tube out slightly and they will push right in. By forcing the injector in you can damage the injector tubes.

Doug
Old 06-08-2005, 09:36 PM
  #5  
Registered User
Thread Starter
 
caper's Avatar
 
Join Date: Dec 2004
Location: Cape Breton,N.S / Ft Mac AB
Posts: 611
Likes: 0
Received 1 Like on 1 Post
Yes I lubed o ring and pulled out tubes far enough , trust me I,m 6'4 260 and had both thumbs on them givin them hell and wouldn't go in. put the handle of the hammer in them to gently apply more pressure ans they would snap in, just wonderin if that was normal but I guess not. The old ones came out with the bolt in them and just pulling up on them by hand.Weird eh.
Old 06-09-2005, 10:11 PM
  #6  
Banned
 
BigBlue's Avatar
 
Join Date: Feb 2002
Posts: 0
Likes: 0
Received 0 Likes on 0 Posts
I had to give mine a pretty good push when I installed them. My mileage increased after I installed them. I've been pretty hard on this tank (80-90mph on a 200 mile round trip with lots of racing and the comp on 5X5) and I'm sitting at 285 miles on half a tank. Before I would be lucky to get 220 driving like this.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
fiveology
Performance and Accessories 2nd gen only
4
05-01-2008 02:33 PM
jwb600
HELP!
5
10-13-2007 04:15 PM
DodgeDemon
3rd Gen High Performance and Accessories (5.9L Only)
4
06-30-2007 01:44 PM
abc4yew
3rd Gen High Performance and Accessories (5.9L Only)
1
05-19-2006 09:38 AM
PourinDiesel
Performance and Accessories 2nd gen only
4
09-22-2004 06:23 AM



Quick Reply: injector install experts????



All times are GMT -5. The time now is 06:24 PM.