Denver Off-Road Bumpers Installed
#1
Registered User
Thread Starter
Denver Off-Road Bumpers Installed
My brother and I drove up to Fruita last week and picked up some new treats. He got a DOR front bumper for his '96 Suburban and I got DOR front and rear bumpers for my '00 Dodge.
I must say the quality of Layne's work is incredible. These were well worth the wait. I have been wanting these ever since I first saw the original Earthroamer back in 2000.
If you notice from the pictures, I have changed from the Sport grill to the regular one. I felt I wanted a little chrome on the front. I also picked up a valance that bolts to the bottom of the bumper. It is all aluminum. I could have waited for it to be powdercoated, but I just figured I would just have it done locally and save on the shipping since I was already there. I will be adding lights in the next few weeks.
On the rear, I had to remove the light strip from the tailgate. It would hit the bumper. It is fine, because I am planning on getting one of those louvered tailgates anyway.
Here is one pic, the rest are in my gallery.
I must say the quality of Layne's work is incredible. These were well worth the wait. I have been wanting these ever since I first saw the original Earthroamer back in 2000.
If you notice from the pictures, I have changed from the Sport grill to the regular one. I felt I wanted a little chrome on the front. I also picked up a valance that bolts to the bottom of the bumper. It is all aluminum. I could have waited for it to be powdercoated, but I just figured I would just have it done locally and save on the shipping since I was already there. I will be adding lights in the next few weeks.
On the rear, I had to remove the light strip from the tailgate. It would hit the bumper. It is fine, because I am planning on getting one of those louvered tailgates anyway.
Here is one pic, the rest are in my gallery.
#3
Administrator
Also, what the silver disc shown in this pic?
The Suburban one has it also.
Is it a logo/badge he's putting on them now?, as mine is naked, no hint as to who made the bumper.
See, no disc.
phox
The Suburban one has it also.
Is it a logo/badge he's putting on them now?, as mine is naked, no hint as to who made the bumper.
See, no disc.
phox
#5
Registered User
Thread Starter
The valance is made for these bumpers by Layne. It is like .375" aluminum. Not really a skid plate, but like you said much sturdier than the factory piece. They bolt up with eight bolts. Give Layne a call and I would bet he can get you one for your bumper. He did not have one that was powdercoated while I was there, so I got one bare. I will either have it coated locally or I will paint it myself.
Did you notice the new powdercoat he is using? It is a wrinkle like finish. It looks really great!
Yes, the little disc is his logo. It has Denver Off-Road and his phone number.
Michael
Did you notice the new powdercoat he is using? It is a wrinkle like finish. It looks really great!
Yes, the little disc is his logo. It has Denver Off-Road and his phone number.
Michael
Trending Topics
#8
Registered User
Originally posted by mkubacak
The valance is made for these bumpers by Layne. It is like .375" aluminum.
Did you notice the new powdercoat he is using? It is a wrinkle like finish. It looks really great!
Michael
The valance is made for these bumpers by Layne. It is like .375" aluminum.
Did you notice the new powdercoat he is using? It is a wrinkle like finish. It looks really great!
Michael
That valance really makes a difference....looks mean! .375" may not qualify as a full skid plate, but it's sure sounds close....depending on the grade AL used!
Really like the flatter finish to the powercoat...and the chrome grill sets it off beautifully!
Shoe - No real web site that I could ever find, when I dealt with Lane...just articles about his work! Can contact here...he's actually in the Grand Jct area now...phone # is correct.
Attention: Layne Wright
4401 Dixon Drive
Westminster, CO 80031
Phone (970) 858-4010
Email: denveroffroad@yahoo.com
RJ
#9
Registered User
Thread Starter
Thanks to all for your compliments.
I can now stop cringing every time I see a deer or antelope on the side of the road or on the road. I am still dreading that first scratch or dent, but at least I have some protection.
The valance is made from good stuff. It has 6061-T6 printed on it. Only downside in terms of use as a real skid plate, is that it only attaches to the base of the bumper. If it was a little longer and attached to the frame, then there would be some more strength. I am sure it will be sufficient to knock the heads of rabbits and coyotes down.
.
I can now stop cringing every time I see a deer or antelope on the side of the road or on the road. I am still dreading that first scratch or dent, but at least I have some protection.
The valance is made from good stuff. It has 6061-T6 printed on it. Only downside in terms of use as a real skid plate, is that it only attaches to the base of the bumper. If it was a little longer and attached to the frame, then there would be some more strength. I am sure it will be sufficient to knock the heads of rabbits and coyotes down.
.
#11
Registered User
Always wondered about the lack of "air holes" on Layne's bumpers...much less ventilation than the UTE's that he sells (even with a winch). My first thought would be, with the big Dodge grill, it would make no difference.
Phox - Did you ever notice higher trans temps/egt's at hwy speeds...or easier over heating of coolant?
mkubacak - Where are you?...Hot climate area? Wonder if the valance reduces air flow and if it makes any difference?
I know my UTE was made for desert temps...just wondering if all the holes in the UTE make any real contribution? (see my gallery, if unfamiliar). This will be my first summer with it.
We just had this last week of 90* OAT and, come to think of it, my tranny has seen some higher temps than I remember from last yr. Nothing serious, but at hwy cruise, with no traffic in front of me to block flow to the tranny cooler, tranny fluids stabilized at 160*....use to be 140* (empty).
Have seen no difference in EGT's or coolant temps...yet.
Anybody done any testing...or have any thoughts on this subject?
RJ
Phox - Did you ever notice higher trans temps/egt's at hwy speeds...or easier over heating of coolant?
mkubacak - Where are you?...Hot climate area? Wonder if the valance reduces air flow and if it makes any difference?
I know my UTE was made for desert temps...just wondering if all the holes in the UTE make any real contribution? (see my gallery, if unfamiliar). This will be my first summer with it.
We just had this last week of 90* OAT and, come to think of it, my tranny has seen some higher temps than I remember from last yr. Nothing serious, but at hwy cruise, with no traffic in front of me to block flow to the tranny cooler, tranny fluids stabilized at 160*....use to be 140* (empty).
Have seen no difference in EGT's or coolant temps...yet.
Anybody done any testing...or have any thoughts on this subject?
RJ
#13
Administrator
Originally posted by rjohnson
Phox - Did you ever notice higher trans temps/egt's at hwy speeds...or easier over heating of coolant?
Phox - Did you ever notice higher trans temps/egt's at hwy speeds...or easier over heating of coolant?
I was worried about engine temps,
so I kept an eye on them just prior to putting the bumper on, and just after for comparison.
I installed the bumper in mid July, almost the hottest month in Utah,
and didn't notice any engine temp difference at all.
Now that I have the guages, I do notice hotter than usual tranny temps, but don't know if that is due to the bumper, or just a crappy tranny cooler on my truck.
Mainly while offroading, not much forward motion to move the air over, I can get it to 250 in no time,
highway speeds it doesn't seem to be running hot at all, right around 150-160.
EGT's are right where they should be, according to others posts.
phox
#14
Registered User
Thread Starter
Originally posted by rjohnson
mkubacak - Where are you?...Hot climate area? Wonder if the valance reduces air flow and if it makes any difference?
RJ
mkubacak - Where are you?...Hot climate area? Wonder if the valance reduces air flow and if it makes any difference?
RJ
Everything is copacetic for now, I will let ya'll know if I see any problems once I put five tons or so behind it.
Does anyone know how I can get rid of this huge freaking grin on my face? My wife is getting worried it may be terminal. And she is tired of me asking if she has see these cool bumpers.
#15
Registered User
Originally posted by mkubacak
I am on the South Plains of Texas, aka the Llano Estacado(Staked Plains)
I will let ya'll know if I see any problems once I put five tons or so behind it.
I am on the South Plains of Texas, aka the Llano Estacado(Staked Plains)
I will let ya'll know if I see any problems once I put five tons or so behind it.
Towing should be a good test! With non automatic, any shortage of airflow will probably only show in your coolant temps.
I have noticed slightly higher tranny fluid temps only. My oil temp has not increased from last summer...due to bumper. 190* when OAT is below 90*....up to 200* when over 90* outside... (210* if I cruise over 75 mph). I mention this because aux. oil cooler is mounted next to Tranny cooler...and both are tucked behind the bumper and get less airflow than with a stock bumper.
I suspect Lane did serious testing and there is nothing to be concerned about. Just curious why our designs are so different, ventilation-wise. Worst case... what's a little higher temperature...when you can look that Coooooool!
Enjoy.
RJ
Thread
Thread Starter
Forum
Replies
Last Post
DUKFVR
3rd Generation Ram - Non Drivetrain - All Years
29
03-29-2007 10:27 PM
LanceK
3rd Gen High Performance and Accessories (5.9L Only)
4
02-12-2007 12:58 PM
C&C Milo
3rd Gen High Performance and Accessories (5.9L Only)
1
01-11-2007 04:08 PM
Commatoze
Performance and Accessories 2nd gen only
20
09-01-2003 08:30 PM