Clutch problems
#1
Registered User
Thread Starter
Join Date: Aug 2007
Location: CA
Posts: 75
Likes: 0
Received 0 Likes
on
0 Posts
Clutch problems
So i drove it home from work yesterday (drove fine) and when i went to back into my driveway it wouldnt go into reverse. clutch pedal feels fine, but the clutch wont disengage. luckily i got it into the spot by shutting the motor off and putting it in gear and starting it. still clutch didnt release. info in thread is correct and truck has 150K miles on what i assume is a stock clutch.
#3
Registered User
Thread Starter
Join Date: Aug 2007
Location: CA
Posts: 75
Likes: 0
Received 0 Likes
on
0 Posts
no leaks, fluid is good and today i pulled the slave cylindar out and everything looks good "i think", i havnt ever had one out before but it all looks good
#4
Advocate of getting the ban button used on him...
My mistake. I thought you said it won't engage but it is the opposite.
Did it or does it make any strange noise? Any other things not quite right before this happened?
Did it or does it make any strange noise? Any other things not quite right before this happened?
#6
It's my pot and I'll stir it if I want to. If you're not careful, I'll stir your's as well!
It is possible that you have an internal leak in the clutch hydraulics. The master cylinder and slave cylinder come as an assembly from Dodge, filled and pre bled. Had a similar problem on a trip recently and was forced to buy the assembly from the dealer as none of the auto parts suppliers had this in stock.
When mine failed, it was without warning. I was at a stop light when suddenly it was a though I had taken my foot off the clutch as the truck wanted to take off into oncoming traffic. Scared my wife badly and sure got my attention in a hurry! Had to stomp hard on the brake while turning the key off. After that, it would go into gear, but two seconds after that, the clutch auto released.
When mine failed, it was without warning. I was at a stop light when suddenly it was a though I had taken my foot off the clutch as the truck wanted to take off into oncoming traffic. Scared my wife badly and sure got my attention in a hurry! Had to stomp hard on the brake while turning the key off. After that, it would go into gear, but two seconds after that, the clutch auto released.
#7
Registered User
Thread Starter
Join Date: Aug 2007
Location: CA
Posts: 75
Likes: 0
Received 0 Likes
on
0 Posts
Sounds like a similair symptom. But my pedal feels fine. If there was an internal leak wouldn't it loose pressure as the fluid releases? But I am gonna look into it tonight. To breake the subject down some more to see if I can get some more help, I can't get the motor to diconnect the tranny at all.
Trending Topics
#8
Registered User
When you pulled the slave off, could you see/feel the fork? If you are close, I have a BSN Master/Slave sitting in the garage if you are interested in trying it. Where are you in CA?
#10
Registered User
Thread Starter
Join Date: Aug 2007
Location: CA
Posts: 75
Likes: 0
Received 0 Likes
on
0 Posts
12 flapper, how did your pedal feel? Is anyone aware of a way to test the hydrolics without replacing them? i am gonna mess with it more tonight, but there is a big difference between a $900 clutch and $150 hydrolics.
#11
Registered User
Join Date: May 2010
Location: Eastern Washington
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
I am going through a similar situation with my '03. I replaced my hydros ($240 from the dealer) and no change. I have an appointment with a good dodge tranny guy in town and will probably end up with a full replacement.
#12
Registered User
Some G56s have tack-welds connecting the shift rail(s) & fork(s) instead of ~1" welds... then the fork can seperate & prevent gear changes - should be able to feel the problem through the ball-detent shifter.
#13
Registered User
Join Date: Jul 2007
Location: Towanda, PA
Posts: 238
Likes: 0
Received 0 Likes
on
0 Posts
I noticed mine failing when backing my camper in and using the clutch alot. When my pedal was pushed in the clutch would start to engage on its own. Sometimes it would be fast sometimes slow and sometimes would not work at all and then I would hop in it and it work fine all day then it would act up. I never felt a spongey and hard or soft pedal it would change were my pedal engage and disangaged the clutch I delt with it for 6 months I changed it with the valair HD kit about 1 hour very easy. The old one I took out had no visaul problems that I could see must be internal. hope that helps
Thread
Thread Starter
Forum
Replies
Last Post
Fishbait
24 Valve Engine and Drivetrain
10
06-06-2006 12:34 PM