Changing Rear End in FL 60
#1
Registered User
Thread Starter
Join Date: Nov 2003
Location: Florence, Kentucky
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
Changing Rear End in FL 60
At 65 MPH, my engine is turning 2900 RPM's. That affects fuel mileage in a big way. I'd like to be turning around 2200 - 2400. Now here's the question:
My Rockwell rear axle is a 433. How big a job would it be to change it to a 355? Would axles need to be changed as well? I've got more than enough low end right now. I start the truck in 2nd from stop. First is low - low.
More importantly, would this change produce the desired RPM and fuel savings?
Thank You!
My Rockwell rear axle is a 433. How big a job would it be to change it to a 355? Would axles need to be changed as well? I've got more than enough low end right now. I start the truck in 2nd from stop. First is low - low.
More importantly, would this change produce the desired RPM and fuel savings?
Thank You!
#2
Re:Changing Rear End in FL 60
The 3.55 will help a lot, especially if you have overdrive. Unless you've done it before or are an extremely good mechanic you should have someone change them for you. The axle shafts will not need to be changed, and your mileage should increase dramatically. Good luck.
4x4
4x4
#3
Registered User
Thread Starter
Join Date: Nov 2003
Location: Florence, Kentucky
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
Re:Changing Rear End in FL 60
Thanks,
I have a mechanic who is capable. There is no way I would even attempt it.
Do you believe I would see a reduction in RPM"s the way I hope to or maybe even better? No overdrive in this truck, it's a five speed.
I have a mechanic who is capable. There is no way I would even attempt it.
Do you believe I would see a reduction in RPM"s the way I hope to or maybe even better? No overdrive in this truck, it's a five speed.
#4
Registered User
Re:Changing Rear End in FL 60
I guess that fifth gear is overdrive. Your owner's manual should have that info.
By ratio, your RPM with 3.55 gears at 65 MPH would be 2377. However, if you pull your 5er at its max safe speed stated in the manual, 55 MPH, your RPM with present gearing would be 2454. That would maintain the pulling power you now enjoy and also produce higher milage.
It's not only your RPM spoiling your milage, but also your speed. Between 2454 RPM and 2900 RPM there's no increase in torque but a large increase in horsepower produced. That increase in horsepower is needed to overcome the increased air resistance of pushing your rig at 65 instead of 55. Making more horsepower requires more fuel, but you knew that.
Have a look at this http://www.rversonline.org/fueleconomy.htm
Especially read the first sentence after the graph. I know this is not your or my rig in the study, but it does apply somewhat to all of us.
By ratio, your RPM with 3.55 gears at 65 MPH would be 2377. However, if you pull your 5er at its max safe speed stated in the manual, 55 MPH, your RPM with present gearing would be 2454. That would maintain the pulling power you now enjoy and also produce higher milage.
It's not only your RPM spoiling your milage, but also your speed. Between 2454 RPM and 2900 RPM there's no increase in torque but a large increase in horsepower produced. That increase in horsepower is needed to overcome the increased air resistance of pushing your rig at 65 instead of 55. Making more horsepower requires more fuel, but you knew that.
Have a look at this http://www.rversonline.org/fueleconomy.htm
Especially read the first sentence after the graph. I know this is not your or my rig in the study, but it does apply somewhat to all of us.
Thread
Thread Starter
Forum
Replies
Last Post
DLittle
1st Gen. Ram - All Topics
17
04-13-2010 08:52 AM
doorguy
3rd Gen Engine and Drivetrain -> 2003-2007
3
06-08-2007 06:19 AM
supr
24 Valve Engine and Drivetrain
15
08-04-2004 03:33 PM
royta
1st Gen. Ram - All Topics
8
07-13-2004 06:54 PM